| Message ID | 1510253136-14153-3-git-send-email-tharvey@gateworks.com |
|---|---|
| State | Changes Requested, archived |
| Headers | show |
| Series | TDA1997x HDMI video receiver | expand |
Hi Tim, On Thu, Nov 09, 2017 at 10:45:33AM -0800, Tim Harvey wrote: > Cc: Rob Herring <robh@kernel.org> > Signed-off-by: Tim Harvey <tharvey@gateworks.com> > --- > v3: > - fix typo > > v2: > - add vendor prefix and remove _ from vidout-portcfg > - remove _ from labels > - remove max-pixel-rate property > - describe and provide example for single output port > - update to new audio port bindings > --- > .../devicetree/bindings/media/i2c/tda1997x.txt | 179 +++++++++++++++++++++ > 1 file changed, 179 insertions(+) > create mode 100644 Documentation/devicetree/bindings/media/i2c/tda1997x.txt > > diff --git a/Documentation/devicetree/bindings/media/i2c/tda1997x.txt b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt > new file mode 100644 > index 0000000..dd37f14 > --- /dev/null > +++ b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt > @@ -0,0 +1,179 @@ > +Device-Tree bindings for the NXP TDA1997x HDMI receiver > + > +The TDA19971/73 are HDMI video receivers. > + > +The TDA19971 Video port output pins can be used as follows: > + - RGB 8bit per color (24 bits total): R[11:4] B[11:4] G[11:4] > + - YUV444 8bit per color (24 bits total): Y[11:4] Cr[11:4] Cb[11:4] > + - YUV422 semi-planar 8bit per component (16 bits total): Y[11:4] CbCr[11:4] > + - YUV422 semi-planar 10bit per component (20 bits total): Y[11:2] CbCr[11:2] > + - YUV422 semi-planar 12bit per component (24 bits total): - Y[11:0] CbCr[11:0] > + - YUV422 BT656 8bit per component (8 bits total): YCbCr[11:4] (2-cycles) > + - YUV422 BT656 10bit per component (10 bits total): YCbCr[11:2] (2-cycles) > + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles) > + > +The TDA19973 Video port output pins can be used as follows: > + - RGB 12bit per color (36 bits total): R[11:0] B[11:0] G[11:0] > + - YUV444 12bit per color (36 bits total): Y[11:0] Cb[11:0] Cr[11:0] > + - YUV422 semi-planar 12bit per component (24 bits total): Y[11:0] CbCr[11:0] > + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles) > + > +The Video port output pins are mapped via 4-bit 'pin groups' allowing > +for a variety of connection possibilities including swapping pin order within > +pin groups. The video_portcfg device-tree property consists of register mapping > +pairs which map a chip-specific VP output register to a 4-bit pin group. If > +the pin group needs to be bit-swapped you can use the *_S pin-group defines. > + > +Required Properties: > + - compatible : > + - "nxp,tda19971" for the TDA19971 > + - "nxp,tda19973" for the TDA19973 > + - reg : I2C slave address > + - interrupts : The interrupt number > + - DOVDD-supply : Digital I/O supply > + - DVDD-supply : Digital Core supply > + - AVDD-supply : Analog supply > + - nxp,vidout-portcfg : array of pairs mapping VP output pins to pin groups. > + > +Optional Properties: > + - nxp,audout-format : DAI bus format: "i2s" or "spdif". > + - nxp,audout-width : width of audio output data bus (1-4). > + - nxp,audout-layout : data layout (0=AP0 used, 1=AP0/AP1/AP2/AP3 used). > + - nxp,audout-mclk-fs : Multiplication factor between stream rate and codec > + mclk. > + > +The device node must contain one 'port' child node for its digital output > +video port, in accordance with the video interface bindings defined in > +Documentation/devicetree/bindings/media/video-interfaces.txt. Could you add that this port has one endpoint node as well? (Unless you support multiple, that is.) > + > +Optional Endpoint Properties: > + The following three properties are defined in video-interfaces.txt and > + are valid for source endpoints only: Transmitters? Don't you have an endpoint only in the port representing the transmitter? > + - hsync-active: Horizontal synchronization polarity. Defaults to active high. > + - vsync-active: Vertical synchronization polarity. Defaults to active high. > + - data-active: Data polarity. Defaults to active high. > + > +Examples: > + - VP[15:0] connected to IMX6 CSI_DATA[19:4] for 16bit YUV422 > + 16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins) > + hdmi-receiver@48 { > + compatible = "nxp,tda19971"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_tda1997x>; > + reg = <0x48>; > + interrupt-parent = <&gpio1>; > + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; > + DOVDD-supply = <®_3p3v>; > + AVDD-supply = <®_1p8v>; > + DVDD-supply = <®_1p8v>; > + /* audio */ > + #sound-dai-cells = <0>; > + nxp,audout-format = "i2s"; > + nxp,audout-layout = <0>; > + nxp,audout-width = <16>; > + nxp,audout-mclk-fs = <128>; > + /* > + * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4] > + * and Y[11:4] across 16bits in the same pixclk cycle. > + */ > + nxp,vidout-portcfg = > + /* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */ > + < TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >, > + /* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */ > + < TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >, > + /* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */ > + < TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >, > + /* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */ > + < TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >; > + > + port { > + tda1997x_to_ipu1_csi0_mux: endpoint { > + remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>; > + bus-width = <16>; > + hsync-active = <1>; > + vsync-active = <1>; > + data-active = <1>; > + }; > + }; > + }; > + - VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656 > + 16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins) > + hdmi-receiver@48 { > + compatible = "nxp,tda19971"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_tda1997x>; > + reg = <0x48>; > + interrupt-parent = <&gpio1>; > + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; > + DOVDD-supply = <®_3p3v>; > + AVDD-supply = <®_1p8v>; > + DVDD-supply = <®_1p8v>; > + /* audio */ > + #sound-dai-cells = <0>; > + nxp,audout-format = "i2s"; > + nxp,audout-layout = <0>; > + nxp,audout-width = <16>; > + nxp,audout-mclk-fs = <128>; > + /* > + * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4] > + * and Y[11:4] across 16bits in the same pixclk cycle. > + */ > + nxp,vidout-portcfg = > + /* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */ > + < TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >, > + /* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */ > + < TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >, > + /* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */ > + < TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >, > + /* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */ > + < TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >; > + > + port { > + tda1997x_to_ipu1_csi0_mux: endpoint { > + remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>; > + bus-width = <16>; > + hsync-active = <1>; > + vsync-active = <1>; > + data-active = <1>; > + }; > + }; > + }; > + - VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656 > + 16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins) > + hdmi-receiver@48 { > + compatible = "nxp,tda19971"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_tda1997x>; > + reg = <0x48>; > + interrupt-parent = <&gpio1>; > + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; > + DOVDD-supply = <®_3p3v>; > + AVDD-supply = <®_1p8v>; > + DVDD-supply = <®_1p8v>; > + /* audio */ > + #sound-dai-cells = <0>; > + nxp,audout-format = "i2s"; > + nxp,audout-layout = <0>; > + nxp,audout-width = <16>; > + nxp,audout-mclk-fs = <128>; > + /* > + * The 8bpp BT656 mode outputs YCbCr[11:4] across 8bits over > + * 2 pixclk cycles. > + */ > + nxp,vidout-portcfg = > + /* YCbCr[11:8]<->VP[15:12]<->CSI_DATA[19:16] */ > + < TDA1997X_VP24_V15_12 TDA1997X_R_CR_CBCR_11_8 >, > + /* YCbCr[7:4]<->VP[11:08]<->CSI_DATA[15:12] */ > + < TDA1997X_VP24_V11_08 TDA1997X_R_CR_CBCR_7_4 >, > + > + port { > + tda1997x_to_ipu1_csi0_mux: endpoint { > + remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>; > + bus-width = <16>; > + hsync-active = <1>; > + vsync-active = <1>; > + data-active = <1>; > + }; > + }; > + }; > + > -- > 2.7.4 >
On Tue, Nov 21, 2017 at 11:36 PM, Sakari Ailus <sakari.ailus@iki.fi> wrote: > Hi Tim, > > On Thu, Nov 09, 2017 at 10:45:33AM -0800, Tim Harvey wrote: >> Cc: Rob Herring <robh@kernel.org> >> Signed-off-by: Tim Harvey <tharvey@gateworks.com> >> --- >> v3: >> - fix typo >> >> v2: >> - add vendor prefix and remove _ from vidout-portcfg >> - remove _ from labels >> - remove max-pixel-rate property >> - describe and provide example for single output port >> - update to new audio port bindings >> --- >> .../devicetree/bindings/media/i2c/tda1997x.txt | 179 +++++++++++++++++++++ >> 1 file changed, 179 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/media/i2c/tda1997x.txt >> >> diff --git a/Documentation/devicetree/bindings/media/i2c/tda1997x.txt b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt >> new file mode 100644 >> index 0000000..dd37f14 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt >> @@ -0,0 +1,179 @@ >> +Device-Tree bindings for the NXP TDA1997x HDMI receiver >> + >> +The TDA19971/73 are HDMI video receivers. >> + >> +The TDA19971 Video port output pins can be used as follows: >> + - RGB 8bit per color (24 bits total): R[11:4] B[11:4] G[11:4] >> + - YUV444 8bit per color (24 bits total): Y[11:4] Cr[11:4] Cb[11:4] >> + - YUV422 semi-planar 8bit per component (16 bits total): Y[11:4] CbCr[11:4] >> + - YUV422 semi-planar 10bit per component (20 bits total): Y[11:2] CbCr[11:2] >> + - YUV422 semi-planar 12bit per component (24 bits total): - Y[11:0] CbCr[11:0] >> + - YUV422 BT656 8bit per component (8 bits total): YCbCr[11:4] (2-cycles) >> + - YUV422 BT656 10bit per component (10 bits total): YCbCr[11:2] (2-cycles) >> + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles) >> + >> +The TDA19973 Video port output pins can be used as follows: >> + - RGB 12bit per color (36 bits total): R[11:0] B[11:0] G[11:0] >> + - YUV444 12bit per color (36 bits total): Y[11:0] Cb[11:0] Cr[11:0] >> + - YUV422 semi-planar 12bit per component (24 bits total): Y[11:0] CbCr[11:0] >> + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles) >> + >> +The Video port output pins are mapped via 4-bit 'pin groups' allowing >> +for a variety of connection possibilities including swapping pin order within >> +pin groups. The video_portcfg device-tree property consists of register mapping >> +pairs which map a chip-specific VP output register to a 4-bit pin group. If >> +the pin group needs to be bit-swapped you can use the *_S pin-group defines. >> + >> +Required Properties: >> + - compatible : >> + - "nxp,tda19971" for the TDA19971 >> + - "nxp,tda19973" for the TDA19973 >> + - reg : I2C slave address >> + - interrupts : The interrupt number >> + - DOVDD-supply : Digital I/O supply >> + - DVDD-supply : Digital Core supply >> + - AVDD-supply : Analog supply >> + - nxp,vidout-portcfg : array of pairs mapping VP output pins to pin groups. >> + >> +Optional Properties: >> + - nxp,audout-format : DAI bus format: "i2s" or "spdif". >> + - nxp,audout-width : width of audio output data bus (1-4). >> + - nxp,audout-layout : data layout (0=AP0 used, 1=AP0/AP1/AP2/AP3 used). >> + - nxp,audout-mclk-fs : Multiplication factor between stream rate and codec >> + mclk. >> + >> +The device node must contain one 'port' child node for its digital output >> +video port, in accordance with the video interface bindings defined in >> +Documentation/devicetree/bindings/media/video-interfaces.txt. > > Could you add that this port has one endpoint node as well? (Unless you > support multiple, that is.) Sure... will clarify as: The device node must contain one endpoint 'port' child node for its digital output video port, in accordance with the video interface bindings defined in Documentation/devicetree/bindings/media/video-interfaces.txt. >> + >> +Optional Endpoint Properties: >> + The following three properties are defined in video-interfaces.txt and >> + are valid for source endpoints only: > > Transmitters? Don't you have an endpoint only in the port representing the > transmitter? I'm not usre what you mean. The TDA1997x is an HDMI receiver meaning it receives HDMI and decodes it to a parallel video bus. HDMI transmitters are the opposite. Regards, Tim -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Wed, Nov 22, 2017 at 08:37:04PM -0800, Tim Harvey wrote: > On Tue, Nov 21, 2017 at 11:36 PM, Sakari Ailus <sakari.ailus@iki.fi> wrote: > > Hi Tim, > > > > On Thu, Nov 09, 2017 at 10:45:33AM -0800, Tim Harvey wrote: > >> Cc: Rob Herring <robh@kernel.org> > >> Signed-off-by: Tim Harvey <tharvey@gateworks.com> > >> --- > >> v3: > >> - fix typo > >> > >> v2: > >> - add vendor prefix and remove _ from vidout-portcfg > >> - remove _ from labels > >> - remove max-pixel-rate property > >> - describe and provide example for single output port > >> - update to new audio port bindings > >> --- > >> .../devicetree/bindings/media/i2c/tda1997x.txt | 179 +++++++++++++++++++++ > >> 1 file changed, 179 insertions(+) > >> create mode 100644 Documentation/devicetree/bindings/media/i2c/tda1997x.txt > >> > >> diff --git a/Documentation/devicetree/bindings/media/i2c/tda1997x.txt b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt > >> new file mode 100644 > >> index 0000000..dd37f14 > >> --- /dev/null > >> +++ b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt > >> @@ -0,0 +1,179 @@ > >> +Device-Tree bindings for the NXP TDA1997x HDMI receiver > >> + > >> +The TDA19971/73 are HDMI video receivers. > >> + > >> +The TDA19971 Video port output pins can be used as follows: > >> + - RGB 8bit per color (24 bits total): R[11:4] B[11:4] G[11:4] > >> + - YUV444 8bit per color (24 bits total): Y[11:4] Cr[11:4] Cb[11:4] > >> + - YUV422 semi-planar 8bit per component (16 bits total): Y[11:4] CbCr[11:4] > >> + - YUV422 semi-planar 10bit per component (20 bits total): Y[11:2] CbCr[11:2] > >> + - YUV422 semi-planar 12bit per component (24 bits total): - Y[11:0] CbCr[11:0] > >> + - YUV422 BT656 8bit per component (8 bits total): YCbCr[11:4] (2-cycles) > >> + - YUV422 BT656 10bit per component (10 bits total): YCbCr[11:2] (2-cycles) > >> + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles) > >> + > >> +The TDA19973 Video port output pins can be used as follows: > >> + - RGB 12bit per color (36 bits total): R[11:0] B[11:0] G[11:0] > >> + - YUV444 12bit per color (36 bits total): Y[11:0] Cb[11:0] Cr[11:0] > >> + - YUV422 semi-planar 12bit per component (24 bits total): Y[11:0] CbCr[11:0] > >> + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles) > >> + > >> +The Video port output pins are mapped via 4-bit 'pin groups' allowing > >> +for a variety of connection possibilities including swapping pin order within > >> +pin groups. The video_portcfg device-tree property consists of register mapping > >> +pairs which map a chip-specific VP output register to a 4-bit pin group. If > >> +the pin group needs to be bit-swapped you can use the *_S pin-group defines. > >> + > >> +Required Properties: > >> + - compatible : > >> + - "nxp,tda19971" for the TDA19971 > >> + - "nxp,tda19973" for the TDA19973 > >> + - reg : I2C slave address > >> + - interrupts : The interrupt number > >> + - DOVDD-supply : Digital I/O supply > >> + - DVDD-supply : Digital Core supply > >> + - AVDD-supply : Analog supply > >> + - nxp,vidout-portcfg : array of pairs mapping VP output pins to pin groups. > >> + > >> +Optional Properties: > >> + - nxp,audout-format : DAI bus format: "i2s" or "spdif". > >> + - nxp,audout-width : width of audio output data bus (1-4). > >> + - nxp,audout-layout : data layout (0=AP0 used, 1=AP0/AP1/AP2/AP3 used). > >> + - nxp,audout-mclk-fs : Multiplication factor between stream rate and codec > >> + mclk. > >> + > >> +The device node must contain one 'port' child node for its digital output > >> +video port, in accordance with the video interface bindings defined in > >> +Documentation/devicetree/bindings/media/video-interfaces.txt. > > > > Could you add that this port has one endpoint node as well? (Unless you > > support multiple, that is.) > > Sure... will clarify as: > > The device node must contain one endpoint 'port' child node for its > digital output > video port, in accordance with the video interface bindings defined in > Documentation/devicetree/bindings/media/video-interfaces.txt. I think it'd be clearer if you just add "The port node shall contain one endpoint child node". > > >> + > >> +Optional Endpoint Properties: > >> + The following three properties are defined in video-interfaces.txt and > >> + are valid for source endpoints only: > > > > Transmitters? Don't you have an endpoint only in the port representing the > > transmitter? > > I'm not usre what you mean. > > The TDA1997x is an HDMI receiver meaning it receives HDMI and decodes > it to a parallel video bus. HDMI transmitters are the opposite. The parallel bus. If you mean that, then you could just say that. "Source endpoint" is a bit vague, or requires knowing V4L2.
On Thu, Nov 23, 2017 at 12:25 AM, Sakari Ailus <sakari.ailus@iki.fi> wrote: > On Wed, Nov 22, 2017 at 08:37:04PM -0800, Tim Harvey wrote: >> On Tue, Nov 21, 2017 at 11:36 PM, Sakari Ailus <sakari.ailus@iki.fi> wrote: >> > Hi Tim, >> > >> > On Thu, Nov 09, 2017 at 10:45:33AM -0800, Tim Harvey wrote: >> >> Cc: Rob Herring <robh@kernel.org> >> >> Signed-off-by: Tim Harvey <tharvey@gateworks.com> >> >> --- >> >> v3: >> >> - fix typo >> >> >> >> v2: >> >> - add vendor prefix and remove _ from vidout-portcfg >> >> - remove _ from labels >> >> - remove max-pixel-rate property >> >> - describe and provide example for single output port >> >> - update to new audio port bindings >> >> --- >> >> .../devicetree/bindings/media/i2c/tda1997x.txt | 179 +++++++++++++++++++++ >> >> 1 file changed, 179 insertions(+) >> >> create mode 100644 Documentation/devicetree/bindings/media/i2c/tda1997x.txt >> >> >> >> diff --git a/Documentation/devicetree/bindings/media/i2c/tda1997x.txt b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt >> >> new file mode 100644 >> >> index 0000000..dd37f14 >> >> --- /dev/null >> >> +++ b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt >> >> @@ -0,0 +1,179 @@ >> >> +Device-Tree bindings for the NXP TDA1997x HDMI receiver >> >> + >> >> +The TDA19971/73 are HDMI video receivers. >> >> + >> >> +The TDA19971 Video port output pins can be used as follows: >> >> + - RGB 8bit per color (24 bits total): R[11:4] B[11:4] G[11:4] >> >> + - YUV444 8bit per color (24 bits total): Y[11:4] Cr[11:4] Cb[11:4] >> >> + - YUV422 semi-planar 8bit per component (16 bits total): Y[11:4] CbCr[11:4] >> >> + - YUV422 semi-planar 10bit per component (20 bits total): Y[11:2] CbCr[11:2] >> >> + - YUV422 semi-planar 12bit per component (24 bits total): - Y[11:0] CbCr[11:0] >> >> + - YUV422 BT656 8bit per component (8 bits total): YCbCr[11:4] (2-cycles) >> >> + - YUV422 BT656 10bit per component (10 bits total): YCbCr[11:2] (2-cycles) >> >> + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles) >> >> + >> >> +The TDA19973 Video port output pins can be used as follows: >> >> + - RGB 12bit per color (36 bits total): R[11:0] B[11:0] G[11:0] >> >> + - YUV444 12bit per color (36 bits total): Y[11:0] Cb[11:0] Cr[11:0] >> >> + - YUV422 semi-planar 12bit per component (24 bits total): Y[11:0] CbCr[11:0] >> >> + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles) >> >> + >> >> +The Video port output pins are mapped via 4-bit 'pin groups' allowing >> >> +for a variety of connection possibilities including swapping pin order within >> >> +pin groups. The video_portcfg device-tree property consists of register mapping >> >> +pairs which map a chip-specific VP output register to a 4-bit pin group. If >> >> +the pin group needs to be bit-swapped you can use the *_S pin-group defines. >> >> + >> >> +Required Properties: >> >> + - compatible : >> >> + - "nxp,tda19971" for the TDA19971 >> >> + - "nxp,tda19973" for the TDA19973 >> >> + - reg : I2C slave address >> >> + - interrupts : The interrupt number >> >> + - DOVDD-supply : Digital I/O supply >> >> + - DVDD-supply : Digital Core supply >> >> + - AVDD-supply : Analog supply >> >> + - nxp,vidout-portcfg : array of pairs mapping VP output pins to pin groups. >> >> + >> >> +Optional Properties: >> >> + - nxp,audout-format : DAI bus format: "i2s" or "spdif". >> >> + - nxp,audout-width : width of audio output data bus (1-4). >> >> + - nxp,audout-layout : data layout (0=AP0 used, 1=AP0/AP1/AP2/AP3 used). >> >> + - nxp,audout-mclk-fs : Multiplication factor between stream rate and codec >> >> + mclk. >> >> + >> >> +The device node must contain one 'port' child node for its digital output >> >> +video port, in accordance with the video interface bindings defined in >> >> +Documentation/devicetree/bindings/media/video-interfaces.txt. >> > >> > Could you add that this port has one endpoint node as well? (Unless you >> > support multiple, that is.) >> >> Sure... will clarify as: >> >> The device node must contain one endpoint 'port' child node for its >> digital output >> video port, in accordance with the video interface bindings defined in >> Documentation/devicetree/bindings/media/video-interfaces.txt. > > I think it'd be clearer if you just add "The port node shall contain one > endpoint child node". ok > >> >> >> + >> >> +Optional Endpoint Properties: >> >> + The following three properties are defined in video-interfaces.txt and >> >> + are valid for source endpoints only: >> > >> > Transmitters? Don't you have an endpoint only in the port representing the >> > transmitter? >> >> I'm not usre what you mean. >> >> The TDA1997x is an HDMI receiver meaning it receives HDMI and decodes >> it to a parallel video bus. HDMI transmitters are the opposite. > > The parallel bus. If you mean that, then you could just say that. "Source > endpoint" is a bit vague, or requires knowing V4L2. > agreed Thanks, Tim -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/media/i2c/tda1997x.txt b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt new file mode 100644 index 0000000..dd37f14 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt @@ -0,0 +1,179 @@ +Device-Tree bindings for the NXP TDA1997x HDMI receiver + +The TDA19971/73 are HDMI video receivers. + +The TDA19971 Video port output pins can be used as follows: + - RGB 8bit per color (24 bits total): R[11:4] B[11:4] G[11:4] + - YUV444 8bit per color (24 bits total): Y[11:4] Cr[11:4] Cb[11:4] + - YUV422 semi-planar 8bit per component (16 bits total): Y[11:4] CbCr[11:4] + - YUV422 semi-planar 10bit per component (20 bits total): Y[11:2] CbCr[11:2] + - YUV422 semi-planar 12bit per component (24 bits total): - Y[11:0] CbCr[11:0] + - YUV422 BT656 8bit per component (8 bits total): YCbCr[11:4] (2-cycles) + - YUV422 BT656 10bit per component (10 bits total): YCbCr[11:2] (2-cycles) + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles) + +The TDA19973 Video port output pins can be used as follows: + - RGB 12bit per color (36 bits total): R[11:0] B[11:0] G[11:0] + - YUV444 12bit per color (36 bits total): Y[11:0] Cb[11:0] Cr[11:0] + - YUV422 semi-planar 12bit per component (24 bits total): Y[11:0] CbCr[11:0] + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles) + +The Video port output pins are mapped via 4-bit 'pin groups' allowing +for a variety of connection possibilities including swapping pin order within +pin groups. The video_portcfg device-tree property consists of register mapping +pairs which map a chip-specific VP output register to a 4-bit pin group. If +the pin group needs to be bit-swapped you can use the *_S pin-group defines. + +Required Properties: + - compatible : + - "nxp,tda19971" for the TDA19971 + - "nxp,tda19973" for the TDA19973 + - reg : I2C slave address + - interrupts : The interrupt number + - DOVDD-supply : Digital I/O supply + - DVDD-supply : Digital Core supply + - AVDD-supply : Analog supply + - nxp,vidout-portcfg : array of pairs mapping VP output pins to pin groups. + +Optional Properties: + - nxp,audout-format : DAI bus format: "i2s" or "spdif". + - nxp,audout-width : width of audio output data bus (1-4). + - nxp,audout-layout : data layout (0=AP0 used, 1=AP0/AP1/AP2/AP3 used). + - nxp,audout-mclk-fs : Multiplication factor between stream rate and codec + mclk. + +The device node must contain one 'port' child node for its digital output +video port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Optional Endpoint Properties: + The following three properties are defined in video-interfaces.txt and + are valid for source endpoints only: + - hsync-active: Horizontal synchronization polarity. Defaults to active high. + - vsync-active: Vertical synchronization polarity. Defaults to active high. + - data-active: Data polarity. Defaults to active high. + +Examples: + - VP[15:0] connected to IMX6 CSI_DATA[19:4] for 16bit YUV422 + 16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins) + hdmi-receiver@48 { + compatible = "nxp,tda19971"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tda1997x>; + reg = <0x48>; + interrupt-parent = <&gpio1>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + DOVDD-supply = <®_3p3v>; + AVDD-supply = <®_1p8v>; + DVDD-supply = <®_1p8v>; + /* audio */ + #sound-dai-cells = <0>; + nxp,audout-format = "i2s"; + nxp,audout-layout = <0>; + nxp,audout-width = <16>; + nxp,audout-mclk-fs = <128>; + /* + * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4] + * and Y[11:4] across 16bits in the same pixclk cycle. + */ + nxp,vidout-portcfg = + /* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */ + < TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >, + /* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */ + < TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >, + /* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */ + < TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >, + /* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */ + < TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >; + + port { + tda1997x_to_ipu1_csi0_mux: endpoint { + remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>; + bus-width = <16>; + hsync-active = <1>; + vsync-active = <1>; + data-active = <1>; + }; + }; + }; + - VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656 + 16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins) + hdmi-receiver@48 { + compatible = "nxp,tda19971"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tda1997x>; + reg = <0x48>; + interrupt-parent = <&gpio1>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + DOVDD-supply = <®_3p3v>; + AVDD-supply = <®_1p8v>; + DVDD-supply = <®_1p8v>; + /* audio */ + #sound-dai-cells = <0>; + nxp,audout-format = "i2s"; + nxp,audout-layout = <0>; + nxp,audout-width = <16>; + nxp,audout-mclk-fs = <128>; + /* + * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4] + * and Y[11:4] across 16bits in the same pixclk cycle. + */ + nxp,vidout-portcfg = + /* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */ + < TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >, + /* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */ + < TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >, + /* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */ + < TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >, + /* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */ + < TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >; + + port { + tda1997x_to_ipu1_csi0_mux: endpoint { + remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>; + bus-width = <16>; + hsync-active = <1>; + vsync-active = <1>; + data-active = <1>; + }; + }; + }; + - VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656 + 16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins) + hdmi-receiver@48 { + compatible = "nxp,tda19971"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tda1997x>; + reg = <0x48>; + interrupt-parent = <&gpio1>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; + DOVDD-supply = <®_3p3v>; + AVDD-supply = <®_1p8v>; + DVDD-supply = <®_1p8v>; + /* audio */ + #sound-dai-cells = <0>; + nxp,audout-format = "i2s"; + nxp,audout-layout = <0>; + nxp,audout-width = <16>; + nxp,audout-mclk-fs = <128>; + /* + * The 8bpp BT656 mode outputs YCbCr[11:4] across 8bits over + * 2 pixclk cycles. + */ + nxp,vidout-portcfg = + /* YCbCr[11:8]<->VP[15:12]<->CSI_DATA[19:16] */ + < TDA1997X_VP24_V15_12 TDA1997X_R_CR_CBCR_11_8 >, + /* YCbCr[7:4]<->VP[11:08]<->CSI_DATA[15:12] */ + < TDA1997X_VP24_V11_08 TDA1997X_R_CR_CBCR_7_4 >, + + port { + tda1997x_to_ipu1_csi0_mux: endpoint { + remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>; + bus-width = <16>; + hsync-active = <1>; + vsync-active = <1>; + data-active = <1>; + }; + }; + }; +
Cc: Rob Herring <robh@kernel.org> Signed-off-by: Tim Harvey <tharvey@gateworks.com> --- v3: - fix typo v2: - add vendor prefix and remove _ from vidout-portcfg - remove _ from labels - remove max-pixel-rate property - describe and provide example for single output port - update to new audio port bindings --- .../devicetree/bindings/media/i2c/tda1997x.txt | 179 +++++++++++++++++++++ 1 file changed, 179 insertions(+) create mode 100644 Documentation/devicetree/bindings/media/i2c/tda1997x.txt