diff mbox series

[net-next,v2,1/2] dt-bindings: net: add DT bindings for Socionext UniPhier AVE

Message ID 1507854928-4357-2-git-send-email-hayashi.kunihiko@socionext.com
State Changes Requested, archived
Delegated to: David Miller
Headers show
Series add UniPhier AVE ethernet support | expand

Commit Message

Kunihiko Hayashi Oct. 13, 2017, 12:35 a.m. UTC 
DT bindings for the AVE ethernet controller found on Socionext's
UniPhier platforms.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
---
 .../bindings/net/socionext,uniphier-ave4.txt       | 53 ++++++++++++++++++++++
 1 file changed, 53 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt

Comments

Masahiro Yamada Oct. 13, 2017, 4:41 p.m. UTC | #1 
2017-10-13 9:35 GMT+09:00 Kunihiko Hayashi <hayashi.kunihiko@socionext.com>:
> DT bindings for the AVE ethernet controller found on Socionext's
> UniPhier platforms.
>
> Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
> Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
> ---
>  .../bindings/net/socionext,uniphier-ave4.txt       | 53 ++++++++++++++++++++++
>  1 file changed, 53 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt
>
> diff --git a/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt
> new file mode 100644
> index 0000000..25f4d92
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt
> @@ -0,0 +1,53 @@
> +* Socionext AVE ethernet controller
> +
> +This describes the devicetree bindings for AVE ethernet controller
> +implemented on Socionext UniPhier SoCs.
> +
> +Required properties:
> + - compatible: Should be
> +       - "socionext,uniphier-pro4-ave4" : for Pro4 SoC
> +       - "socionext,uniphier-pxs2-ave4" : for PXs2 SoC
> +       - "socionext,uniphier-ld20-ave4" : for LD20 SoC
> +       - "socionext,uniphier-ld11-ave4" : for LD11 SoC

Nit.  LD11, LD20, in this order please.

> + - reg: Address where registers are mapped and size of region.
> + - interrupts: Should contain the MAC interrupt.
> + - phy-mode: See ethernet.txt in the same directory. Allow to choose
> +       "rgmii", "rmii", or "mii" according to the PHY.
> + - pinctrl-names: List of assigned state names, see pinctrl
> +       binding documentation.
> + - pinctrl-0: List of phandles to configure the GPIO pin,


configure the GPIO pin?

git-grep found this phrase.


$ git grep "List of phandles to configure the GPIO"
Documentation/devicetree/bindings/net/microchip,enc28j60.txt:-
pinctrl-0: List of phandles to configure the GPIO pin used as
interrupt line,





> +       see pinctrl binding documentation. Choose this appropriately
> +       according to phy-mode.
> +       - <&pinctrl_ether_rgmii> if phy-mode is "rgmii".
> +       - <&pinctrl_ether_rmii> if phy-mode is "rmii".
> +       - <&pinctrl_ether_mii> if phy-mode is "mii".

pinctrl_ether_rgmii is just a label
you just happened to write in your DT file.

This information is totally unrelated to hardware specification.
It is not stable, either.



> + - phy-handle: Should point to the external phy device.
> +       See ethernet.txt file in the same directory.
> + - mdio subnode: Should be device tree subnode with the following required
> +       properties:
> +       - #address-cells: Must be <1>.
> +       - #size-cells: Must be <0>.
> +       - reg: phy ID number, usually a small integer.


Are you talking about "Required subnode" in the "Required properties"?




> +Optional properties:
> + - local-mac-address: See ethernet.txt in the same directory.
> +
> +Example:
> +
> +       ether: ethernet@65000000 {
> +               compatible = "socionext,uniphier-ld20-ave4";
> +               reg = <0x65000000 0x8500>;
> +               interrupts = <0 66 4>;
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&pinctrl_ether_rgmii>;
> +               phy-mode = "rgmii";
> +               phy-handle = <&ethphy>;
> +               local-mac-address = [00 00 00 00 00 00];
> +               mdio {
> +                       #address-cells = <1>;
> +                       #size-cells = <0>;
> +                       ethphy: ethphy@1 {
> +                               reg = <1>;
> +                       };
> +               };
> +       };
> --
> 2.7.4
>
Masahiro Yamada Oct. 15, 2017, 2:52 p.m. UTC | #2 
2017-10-13 9:35 GMT+09:00 Kunihiko Hayashi <hayashi.kunihiko@socionext.com>:
> DT bindings for the AVE ethernet controller found on Socionext's
> UniPhier platforms.
>
> Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
> Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
> ---
>  .../bindings/net/socionext,uniphier-ave4.txt       | 53 ++++++++++++++++++++++
>  1 file changed, 53 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt
>
> diff --git a/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt
> new file mode 100644
> index 0000000..25f4d92
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt
> @@ -0,0 +1,53 @@
> +* Socionext AVE ethernet controller
> +
> +This describes the devicetree bindings for AVE ethernet controller
> +implemented on Socionext UniPhier SoCs.
> +
> +Required properties:
> + - compatible: Should be
> +       - "socionext,uniphier-pro4-ave4" : for Pro4 SoC
> +       - "socionext,uniphier-pxs2-ave4" : for PXs2 SoC
> +       - "socionext,uniphier-ld20-ave4" : for LD20 SoC
> +       - "socionext,uniphier-ld11-ave4" : for LD11 SoC
> + - reg: Address where registers are mapped and size of region.
> + - interrupts: Should contain the MAC interrupt.
> + - phy-mode: See ethernet.txt in the same directory. Allow to choose
> +       "rgmii", "rmii", or "mii" according to the PHY.
> + - pinctrl-names: List of assigned state names, see pinctrl
> +       binding documentation.
> + - pinctrl-0: List of phandles to configure the GPIO pin,
> +       see pinctrl binding documentation. Choose this appropriately
> +       according to phy-mode.
> +       - <&pinctrl_ether_rgmii> if phy-mode is "rgmii".
> +       - <&pinctrl_ether_rmii> if phy-mode is "rmii".
> +       - <&pinctrl_ether_mii> if phy-mode is "mii".
> + - phy-handle: Should point to the external phy device.
> +       See ethernet.txt file in the same directory.
> + - mdio subnode: Should be device tree subnode with the following required
> +       properties:
> +       - #address-cells: Must be <1>.
> +       - #size-cells: Must be <0>.
> +       - reg: phy ID number, usually a small integer.
> +
> +Optional properties:
> + - local-mac-address: See ethernet.txt in the same directory.
> +
> +Example:
> +
> +       ether: ethernet@65000000 {
> +               compatible = "socionext,uniphier-ld20-ave4";
> +               reg = <0x65000000 0x8500>;
> +               interrupts = <0 66 4>;
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&pinctrl_ether_rgmii>;
> +               phy-mode = "rgmii";
> +               phy-handle = <&ethphy>;
> +               local-mac-address = [00 00 00 00 00 00];
> +               mdio {
> +                       #address-cells = <1>;
> +                       #size-cells = <0>;
> +                       ethphy: ethphy@1 {
> +                               reg = <1>;
> +                       };
> +               };
> +       };
> --
> 2.7.4
>


I found the following code in 2/2.

+ /* get clock */
+ priv->clk = clk_get(dev, NULL);
+ if (IS_ERR(priv->clk))
+ priv->clk = NULL;
+
+ /* get reset */
+ priv->rst = reset_control_get(dev, NULL);
+ if (IS_ERR(priv->rst))
+ priv->rst = NULL;
+


This doc needs to describe "clocks", "resets".
Kunihiko Hayashi Oct. 18, 2017, 10:23 a.m. UTC | #3 
On Sat, 14 Oct 2017 01:41:12 +0900 <yamada.masahiro@socionext.com> wrote:

> 2017-10-13 9:35 GMT+09:00 Kunihiko Hayashi <hayashi.kunihiko@socionext.com>:
> > DT bindings for the AVE ethernet controller found on Socionext's
> > UniPhier platforms.
> >
> > Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
> > Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
> > ---
> >  .../bindings/net/socionext,uniphier-ave4.txt       | 53 ++++++++++++++++++++++
> >  1 file changed, 53 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt
> >
> > diff --git a/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt
> > new file mode 100644
> > index 0000000..25f4d92
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt
> > @@ -0,0 +1,53 @@
> > +* Socionext AVE ethernet controller
> > +
> > +This describes the devicetree bindings for AVE ethernet controller
> > +implemented on Socionext UniPhier SoCs.
> > +
> > +Required properties:
> > + - compatible: Should be
> > +       - "socionext,uniphier-pro4-ave4" : for Pro4 SoC
> > +       - "socionext,uniphier-pxs2-ave4" : for PXs2 SoC
> > +       - "socionext,uniphier-ld20-ave4" : for LD20 SoC
> > +       - "socionext,uniphier-ld11-ave4" : for LD11 SoC
> 
> Nit.  LD11, LD20, in this order please.

I'll fix it. And also the SoC-dependent structures of the driver.

> > + - reg: Address where registers are mapped and size of region.
> > + - interrupts: Should contain the MAC interrupt.
> > + - phy-mode: See ethernet.txt in the same directory. Allow to choose
> > +       "rgmii", "rmii", or "mii" according to the PHY.
> > + - pinctrl-names: List of assigned state names, see pinctrl
> > +       binding documentation.
> > + - pinctrl-0: List of phandles to configure the GPIO pin,
> 
> 
> configure the GPIO pin?
> 
> git-grep found this phrase.
> 
> 
> $ git grep "List of phandles to configure the GPIO"
> Documentation/devicetree/bindings/net/microchip,enc28j60.txt:-
> pinctrl-0: List of phandles to configure the GPIO pin used as
> interrupt line,
> 
> 
> 
> 
> 
> > +       see pinctrl binding documentation. Choose this appropriately
> > +       according to phy-mode.
> > +       - <&pinctrl_ether_rgmii> if phy-mode is "rgmii".
> > +       - <&pinctrl_ether_rmii> if phy-mode is "rmii".
> > +       - <&pinctrl_ether_mii> if phy-mode is "mii".
> 
> pinctrl_ether_rgmii is just a label
> you just happened to write in your DT file.
> 
> This information is totally unrelated to hardware specification.
> It is not stable, either.

Surely this driver is independent from the pinctrl.
I'll remove the descriptions about the pinctrl.

> > + - phy-handle: Should point to the external phy device.
> > +       See ethernet.txt file in the same directory.
> > + - mdio subnode: Should be device tree subnode with the following required
> > +       properties:
> > +       - #address-cells: Must be <1>.
> > +       - #size-cells: Must be <0>.
> > +       - reg: phy ID number, usually a small integer.
> 
> 
> Are you talking about "Required subnode" in the "Required properties"?

It might be confused description. The subnode is separated from the properties.

> > +Optional properties:
> > + - local-mac-address: See ethernet.txt in the same directory.

In addition, I'll add "clocks" and "resets" according to another mail.

> > +
> > +Example:
> > +
> > +       ether: ethernet@65000000 {
> > +               compatible = "socionext,uniphier-ld20-ave4";
> > +               reg = <0x65000000 0x8500>;
> > +               interrupts = <0 66 4>;
> > +               pinctrl-names = "default";
> > +               pinctrl-0 = <&pinctrl_ether_rgmii>;
> > +               phy-mode = "rgmii";
> > +               phy-handle = <&ethphy>;
> > +               local-mac-address = [00 00 00 00 00 00];
> > +               mdio {
> > +                       #address-cells = <1>;
> > +                       #size-cells = <0>;
> > +                       ethphy: ethphy@1 {
> > +                               reg = <1>;
> > +                       };
> > +               };
> > +       };
> > --
> > 2.7.4
> >
> 
> 
> 
> -- 
> Best Regards
> Masahiro Yamada

---
Best Regards,
Kunihiko Hayashi
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt
new file mode 100644
index 0000000..25f4d92
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt
@@ -0,0 +1,53 @@ 
+* Socionext AVE ethernet controller
+
+This describes the devicetree bindings for AVE ethernet controller
+implemented on Socionext UniPhier SoCs.
+
+Required properties:
+ - compatible: Should be
+	- "socionext,uniphier-pro4-ave4" : for Pro4 SoC
+	- "socionext,uniphier-pxs2-ave4" : for PXs2 SoC
+	- "socionext,uniphier-ld20-ave4" : for LD20 SoC
+	- "socionext,uniphier-ld11-ave4" : for LD11 SoC
+ - reg: Address where registers are mapped and size of region.
+ - interrupts: Should contain the MAC interrupt.
+ - phy-mode: See ethernet.txt in the same directory. Allow to choose
+	"rgmii", "rmii", or "mii" according to the PHY.
+ - pinctrl-names: List of assigned state names, see pinctrl
+	binding documentation.
+ - pinctrl-0: List of phandles to configure the GPIO pin,
+	see pinctrl binding documentation. Choose this appropriately
+	according to phy-mode.
+	- <&pinctrl_ether_rgmii> if phy-mode is "rgmii".
+	- <&pinctrl_ether_rmii> if phy-mode is "rmii".
+	- <&pinctrl_ether_mii> if phy-mode is "mii".
+ - phy-handle: Should point to the external phy device.
+	See ethernet.txt file in the same directory.
+ - mdio subnode: Should be device tree subnode with the following required
+	properties:
+	- #address-cells: Must be <1>.
+	- #size-cells: Must be <0>.
+	- reg: phy ID number, usually a small integer.
+
+Optional properties:
+ - local-mac-address: See ethernet.txt in the same directory.
+
+Example:
+
+	ether: ethernet@65000000 {
+		compatible = "socionext,uniphier-ld20-ave4";
+		reg = <0x65000000 0x8500>;
+		interrupts = <0 66 4>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ether_rgmii>;
+		phy-mode = "rgmii";
+		phy-handle = <&ethphy>;
+		local-mac-address = [00 00 00 00 00 00];
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			ethphy: ethphy@1 {
+				reg = <1>;
+			};
+		};
+	};