Message ID | 1505373456-24047-1-git-send-email-yamada.masahiro@socionext.com |
---|---|
State | Not Applicable, archived |
Headers | show |
Series | dt-bindings: nand: denali: reduce the register space in the example | expand |
Hi, i assume arch/arm/boot/dts/socfpga.dtsi should be update as well. Right? On 14.09.2017 09:17, Masahiro Yamada wrote: > This example allocates too much for register regions. Especially, > there are only two registers in the "nand_data" interface of this > hardware (ADDR: 0x00, DATA: 0x10). > > Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> > --- > > Documentation/devicetree/bindings/mtd/denali-nand.txt | 2 +- > 1 file changed, 1 insertion(+), 1 deletion(-) > > diff --git a/Documentation/devicetree/bindings/mtd/denali-nand.txt b/Documentation/devicetree/bindings/mtd/denali-nand.txt > index 504291d..0ee8edb 100644 > --- a/Documentation/devicetree/bindings/mtd/denali-nand.txt > +++ b/Documentation/devicetree/bindings/mtd/denali-nand.txt > @@ -29,7 +29,7 @@ nand: nand@ff900000 { > #address-cells = <1>; > #size-cells = <1>; > compatible = "altr,socfpga-denali-nand"; > - reg = <0xff900000 0x100000>, <0xffb80000 0x10000>; > + reg = <0xff900000 0x20>, <0xffb80000 0x1000>; > reg-names = "nand_data", "denali_reg"; > interrupts = <0 144 4>; > }; > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi. 2017-09-14 17:04 GMT+09:00 Oleksij Rempel <ore@pengutronix.de>: > Hi, > > i assume arch/arm/boot/dts/socfpga.dtsi should be update as well. Right? I think so. (also arch/arm/boot/dts/socfpga_arria10.dtsi in the same way) The wrong property "dma-mask" was removed by commit 60d920d32ca40660e382cf9ccbc236599a49e607. > On 14.09.2017 09:17, Masahiro Yamada wrote: >> >> This example allocates too much for register regions. Especially, >> there are only two registers in the "nand_data" interface of this >> hardware (ADDR: 0x00, DATA: 0x10). >> >> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> >> --- >> >> Documentation/devicetree/bindings/mtd/denali-nand.txt | 2 +- >> 1 file changed, 1 insertion(+), 1 deletion(-) >> >> diff --git a/Documentation/devicetree/bindings/mtd/denali-nand.txt >> b/Documentation/devicetree/bindings/mtd/denali-nand.txt >> index 504291d..0ee8edb 100644 >> --- a/Documentation/devicetree/bindings/mtd/denali-nand.txt >> +++ b/Documentation/devicetree/bindings/mtd/denali-nand.txt >> @@ -29,7 +29,7 @@ nand: nand@ff900000 { >> #address-cells = <1>; >> #size-cells = <1>; >> compatible = "altr,socfpga-denali-nand"; >> - reg = <0xff900000 0x100000>, <0xffb80000 0x10000>; >> + reg = <0xff900000 0x20>, <0xffb80000 0x1000>; >> reg-names = "nand_data", "denali_reg"; >> interrupts = <0 144 4>; >> }; >> > -- > To unsubscribe from this list: send the line "unsubscribe devicetree" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html
On 14.09.2017 10:16, Masahiro Yamada wrote: > Hi. > > > 2017-09-14 17:04 GMT+09:00 Oleksij Rempel <ore@pengutronix.de>: >> Hi, >> >> i assume arch/arm/boot/dts/socfpga.dtsi should be update as well. Right? > > I think so. > (also arch/arm/boot/dts/socfpga_arria10.dtsi in the same way) Hm.. according to https://www.altera.com/en_US/pdfs/literature/hb/cyclone-v/cyclone5_handbook.pdf Table 13-18: NAND Controller Module Data Space Address Range Module Instance Start Address End Address NAND_DATA 0xFF900000 0xFF9FFFFF So <0xff900000 0x100000> seems to be a proper value. > The wrong property "dma-mask" was removed by > commit 60d920d32ca40660e382cf9ccbc236599a49e607. > > > >> On 14.09.2017 09:17, Masahiro Yamada wrote: >>> >>> This example allocates too much for register regions. Especially, >>> there are only two registers in the "nand_data" interface of this >>> hardware (ADDR: 0x00, DATA: 0x10). >>> >>> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> >>> --- >>> >>> Documentation/devicetree/bindings/mtd/denali-nand.txt | 2 +- >>> 1 file changed, 1 insertion(+), 1 deletion(-) >>> >>> diff --git a/Documentation/devicetree/bindings/mtd/denali-nand.txt >>> b/Documentation/devicetree/bindings/mtd/denali-nand.txt >>> index 504291d..0ee8edb 100644 >>> --- a/Documentation/devicetree/bindings/mtd/denali-nand.txt >>> +++ b/Documentation/devicetree/bindings/mtd/denali-nand.txt >>> @@ -29,7 +29,7 @@ nand: nand@ff900000 { >>> #address-cells = <1>; >>> #size-cells = <1>; >>> compatible = "altr,socfpga-denali-nand"; >>> - reg = <0xff900000 0x100000>, <0xffb80000 0x10000>; >>> + reg = <0xff900000 0x20>, <0xffb80000 0x1000>; >>> reg-names = "nand_data", "denali_reg"; >>> interrupts = <0 144 4>; >>> }; >>> >> -- >> To unsubscribe from this list: send the line "unsubscribe devicetree" in >> the body of a message to majordomo@vger.kernel.org >> More majordomo info at http://vger.kernel.org/majordomo-info.html > > > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi. 2017-09-14 18:06 GMT+09:00 Oleksij Rempel <ore@pengutronix.de>: > On 14.09.2017 10:16, Masahiro Yamada wrote: >> >> Hi. >> >> >> 2017-09-14 17:04 GMT+09:00 Oleksij Rempel <ore@pengutronix.de>: >>> >>> Hi, >>> >>> i assume arch/arm/boot/dts/socfpga.dtsi should be update as well. Right? >> >> >> I think so. >> (also arch/arm/boot/dts/socfpga_arria10.dtsi in the same way) > > > Hm.. according to > https://www.altera.com/en_US/pdfs/literature/hb/cyclone-v/cyclone5_handbook.pdf > Table 13-18: NAND Controller Module Data Space Address Range > > Module Instance Start Address End Address > NAND_DATA 0xFF900000 0xFF9FFFFF > > So <0xff900000 0x100000> seems to be a proper value. > The Alrera's SOCFPGA document describes so. It is up to each SoC vendor how to describe the register space. I am focusing on the Denali IP because this IP is used among several SoCs. You can see the peripheral region map starting at page 1-18 of the document you referred to: Slave ID Description Base Addr Size --------------------------------------------------------------- L3REGS L3 interconnect GPV 0xFF800000 1 MB NANDDATA NAND flash controller data 0xFF900000 64 KB QSPIDATA Quad SPI flash data 0xFFA00000 1 MB (In the doc, the base is described as 0xFFB900000, but this is apparently a typo.) The rationale of the "End Address 0xFF9FFFFF" of NAND_DATA is the fact that the base address of the next peripheral (QSPIDATA) is 0xFFA00000. One more, if you look at the next page, Slave ID Description Base Addr Size --------------------------------------------------------------- NANDREGS NAND flash controller registers 0xFFB80000 64 KB FPGAMGRDATA FPGA manager configuration data 0xFFB90000 4 KB The size of NAND register space is described as 64KB, but the rationale is just the start of the next peripheral is 0xFFB90000. (0xFFB90000 - 0xFFB80000 = 0x10000 = 64KB) Altera apparently reserved address space just for the purpose of matching the end address to the base address of the next peripheral. That means, this document specifies address region much bigger than the IP actually provides. If you look at page 13-6, there are only two registers in NANDDATA space. Table 13-4: Register Map for Indexed Addressing Control 0x0 Data 0x10 For NANDREGS, in page 13-106, the following is the last register in the NANDREGS space. lun_status_cmd Offset 0x7A0 Obviously, 0x1000 (4KB) is enough for NANDREGS. To conclude this, this binding document was written based on the Altera's SOCFPGA specification. Altera specifies the region size so that end address matches to the base of the next peripheral. This is just a matter of SOCFPGA address mapping. In my opinion, the binding document should not be oriented to a particular SoC, which is not true for other SoCs.
Hi, On 21.09.2017 07:26, Masahiro Yamada wrote: > Hi. ...... >> Hm.. according to >> https://www.altera.com/en_US/pdfs/literature/hb/cyclone-v/cyclone5_handbook.pdf >> Table 13-18: NAND Controller Module Data Space Address Range >> >> Module Instance Start Address End Address >> NAND_DATA 0xFF900000 0xFF9FFFFF >> >> So <0xff900000 0x100000> seems to be a proper value. >> > > The Alrera's SOCFPGA document describes so. > It is up to each SoC vendor how to describe the register space. > > I am focusing on the Denali IP > because this IP is used among several SoCs. > > > > You can see the peripheral region map > starting at page 1-18 of the document you referred to: > > Slave ID Description Base Addr Size > --------------------------------------------------------------- > L3REGS L3 interconnect GPV 0xFF800000 1 MB > NANDDATA NAND flash controller data 0xFF900000 64 KB > QSPIDATA Quad SPI flash data 0xFFA00000 1 MB > > (In the doc, the base is described as 0xFFB900000, but this is > apparently a typo.) > > > The rationale of the "End Address 0xFF9FFFFF" of NAND_DATA > is the fact that the base address of the next peripheral (QSPIDATA) is > 0xFFA00000. > > > > > One more, if you look at the next page, > > Slave ID Description Base Addr Size > --------------------------------------------------------------- > NANDREGS NAND flash controller registers 0xFFB80000 64 KB > FPGAMGRDATA FPGA manager configuration data 0xFFB90000 4 KB > > > The size of NAND register space is described as 64KB, > but the rationale is just the start of the next peripheral is 0xFFB90000. > > (0xFFB90000 - 0xFFB80000 = 0x10000 = 64KB) > > > > Altera apparently reserved address space just for the purpose > of matching the end address to the base address of the next peripheral. > > > That means, this document specifies address region > much bigger than the IP actually provides. > > > If you look at page 13-6, there are only two registers > in NANDDATA space. > > Table 13-4: Register Map for Indexed Addressing > Control 0x0 > Data 0x10 > > > > For NANDREGS, in page 13-106, the following is the last register > in the NANDREGS space. > > lun_status_cmd > Offset 0x7A0 > > Obviously, 0x1000 (4KB) is enough for NANDREGS. > > To conclude this, this binding document was written > based on the Altera's SOCFPGA specification. > > Altera specifies the region size > so that end address matches to the base of the next peripheral. > This is just a matter of SOCFPGA address mapping. > > In my opinion, the binding document should not be oriented > to a particular SoC, which is not true for other SoCs. ok. Thank you for detailed response. -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
2017-09-21 15:09 GMT+09:00 Oleksij Rempel <ore@pengutronix.de>: > Hi, > > On 21.09.2017 07:26, Masahiro Yamada wrote: >> >> Hi. > > > ...... > >>> Hm.. according to >>> >>> https://www.altera.com/en_US/pdfs/literature/hb/cyclone-v/cyclone5_handbook.pdf >>> Table 13-18: NAND Controller Module Data Space Address Range >>> >>> Module Instance Start Address End Address >>> NAND_DATA 0xFF900000 0xFF9FFFFF >>> >>> So <0xff900000 0x100000> seems to be a proper value. >>> >> >> The Alrera's SOCFPGA document describes so. >> It is up to each SoC vendor how to describe the register space. >> >> I am focusing on the Denali IP >> because this IP is used among several SoCs. >> >> >> >> You can see the peripheral region map >> starting at page 1-18 of the document you referred to: >> >> Slave ID Description Base Addr Size >> --------------------------------------------------------------- >> L3REGS L3 interconnect GPV 0xFF800000 1 MB >> NANDDATA NAND flash controller data 0xFF900000 64 KB >> QSPIDATA Quad SPI flash data 0xFFA00000 1 MB >> >> (In the doc, the base is described as 0xFFB900000, but this is >> apparently a typo.) >> >> >> The rationale of the "End Address 0xFF9FFFFF" of NAND_DATA >> is the fact that the base address of the next peripheral (QSPIDATA) is >> 0xFFA00000. >> >> >> >> >> One more, if you look at the next page, >> >> Slave ID Description Base Addr Size >> --------------------------------------------------------------- >> NANDREGS NAND flash controller registers 0xFFB80000 64 KB >> FPGAMGRDATA FPGA manager configuration data 0xFFB90000 4 KB >> >> >> The size of NAND register space is described as 64KB, >> but the rationale is just the start of the next peripheral is 0xFFB90000. >> >> (0xFFB90000 - 0xFFB80000 = 0x10000 = 64KB) >> >> >> >> Altera apparently reserved address space just for the purpose >> of matching the end address to the base address of the next peripheral. >> >> >> That means, this document specifies address region >> much bigger than the IP actually provides. >> >> >> If you look at page 13-6, there are only two registers >> in NANDDATA space. >> >> Table 13-4: Register Map for Indexed Addressing >> Control 0x0 >> Data 0x10 >> >> >> >> For NANDREGS, in page 13-106, the following is the last register >> in the NANDREGS space. >> >> lun_status_cmd >> Offset 0x7A0 >> >> Obviously, 0x1000 (4KB) is enough for NANDREGS. >> >> To conclude this, this binding document was written >> based on the Altera's SOCFPGA specification. >> >> Altera specifies the region size >> so that end address matches to the base of the next peripheral. >> This is just a matter of SOCFPGA address mapping. >> >> In my opinion, the binding document should not be oriented >> to a particular SoC, which is not true for other SoCs. > > ok. Thank you for detailed response. BTW, I am not forcing you to change the SOCFPGA DTS. It is up to you and Dihn whether change it or not. I do not have any SOCFPGA board.
On Thu, Sep 14, 2017 at 04:17:36PM +0900, Masahiro Yamada wrote: > This example allocates too much for register regions. Especially, > there are only two registers in the "nand_data" interface of this > hardware (ADDR: 0x00, DATA: 0x10). > > Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> > --- > > Documentation/devicetree/bindings/mtd/denali-nand.txt | 2 +- > 1 file changed, 1 insertion(+), 1 deletion(-) Acked-by: Rob Herring <robh@kernel.org> -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/mtd/denali-nand.txt b/Documentation/devicetree/bindings/mtd/denali-nand.txt index 504291d..0ee8edb 100644 --- a/Documentation/devicetree/bindings/mtd/denali-nand.txt +++ b/Documentation/devicetree/bindings/mtd/denali-nand.txt @@ -29,7 +29,7 @@ nand: nand@ff900000 { #address-cells = <1>; #size-cells = <1>; compatible = "altr,socfpga-denali-nand"; - reg = <0xff900000 0x100000>, <0xffb80000 0x10000>; + reg = <0xff900000 0x20>, <0xffb80000 0x1000>; reg-names = "nand_data", "denali_reg"; interrupts = <0 144 4>; };
This example allocates too much for register regions. Especially, there are only two registers in the "nand_data" interface of this hardware (ADDR: 0x00, DATA: 0x10). Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> --- Documentation/devicetree/bindings/mtd/denali-nand.txt | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)