| Message ID | 4982156c-5325-8021-dcd3-f13e02c63c72@candelatech.com |
|---|---|
| State | Rejected |
| Headers | show |
Hi Ben, > The problem I see is that sometimes (and quite often when I am using lots > of vdevs and thus the NIC is busy), the keys are set before the EAPOL 4/4 > hits the air. When the key is set, the NIC will no longer transmit the > frame because of key-length issues in the tx-descriptor (ath10k wave-2 > in this case). We have encountered something similar. In our case we were seeing PAE packets (e.g. 4WayHandshake packet 1 of 4) before seeing the connect events on nl80211. > I suspect that there is a fundamental race between the EAPOL packet-tx > logic and the key-set logic, but supplicant appears to act as though > they are natually synchronized. Fundamentally there is a race between the genl/nl80211 socket to the kernel and the PAE socket that handles the authentication aspects. I think the only way to fix this is to make sure that PAE flows over the genl/nl80211 socket to preserve the proper order of events. However there are lots of dragons in the kernel side of this and we haven't been brave enough to venture into the depths yet :) Regards, -Denis
On 06/08/2017 04:36 PM, Denis Kenzior wrote: > Hi Ben, > >> The problem I see is that sometimes (and quite often when I am using lots >> of vdevs and thus the NIC is busy), the keys are set before the EAPOL 4/4 >> hits the air. When the key is set, the NIC will no longer transmit the >> frame because of key-length issues in the tx-descriptor (ath10k wave-2 >> in this case). > > We have encountered something similar. In our case we were seeing PAE packets (e.g. 4WayHandshake packet 1 of 4) before seeing the connect events on nl80211. > >> I suspect that there is a fundamental race between the EAPOL packet-tx >> logic and the key-set logic, but supplicant appears to act as though >> they are natually synchronized. > > Fundamentally there is a race between the genl/nl80211 socket to the kernel and the PAE socket that handles the authentication aspects. I think the only way to > fix this is to make sure that PAE flows over the genl/nl80211 socket to preserve the proper order of events. However there are lots of dragons in the kernel > side of this and we haven't been brave enough to venture into the depths yet :) I think that would just push the problem lower. Probably a real fix would be to somehow propagate the tx-status for the specific packet back to the supplicant and only then it would know that the key could be set. Thanks, Ben
Hi Ben, On 06/08/2017 06:43 PM, Ben Greear wrote: > On 06/08/2017 04:36 PM, Denis Kenzior wrote: >> Hi Ben, >> >>> The problem I see is that sometimes (and quite often when I am using >>> lots >>> of vdevs and thus the NIC is busy), the keys are set before the EAPOL >>> 4/4 >>> hits the air. When the key is set, the NIC will no longer transmit the >>> frame because of key-length issues in the tx-descriptor (ath10k wave-2 >>> in this case). >> >> We have encountered something similar. In our case we were seeing PAE >> packets (e.g. 4WayHandshake packet 1 of 4) before seeing the connect >> events on nl80211. >> >>> I suspect that there is a fundamental race between the EAPOL packet-tx >>> logic and the key-set logic, but supplicant appears to act as though >>> they are natually synchronized. >> >> Fundamentally there is a race between the genl/nl80211 socket to the >> kernel and the PAE socket that handles the authentication aspects. I >> think the only way to >> fix this is to make sure that PAE flows over the genl/nl80211 socket >> to preserve the proper order of events. However there are lots of >> dragons in the kernel >> side of this and we haven't been brave enough to venture into the >> depths yet :) > > I think that would just push the problem lower. Probably a real fix > would be to somehow propagate > the tx-status for the specific packet back to the supplicant and only > then it would know that the > key could be set. > Having userspace track individual packets in the kernel sounds wrong to me. This also won't help with the packets being received out-of-order. It would be nice if both the RX and TX ordering was preserved. Hence my thinking about running PAE over NL80211. It would then be up to the kernel / drivers to guarantee that the various packets are ordered appropriately. Regardless of the solution, we're happy to help in order to get this fixed. Regards, -Denis
On Thu, 2017-06-08 at 19:07 -0500, Denis Kenzior wrote: > > > Fundamentally there is a race between the genl/nl80211 socket to > > > the > > > kernel and the PAE socket that handles the authentication > > > aspects. I > > > think the only way to > > > fix this is to make sure that PAE flows over the genl/nl80211 > > > socket > > > to preserve the proper order of events. Correct. > > > However there are lots of > > > dragons in the kernel > > > side of this and we haven't been brave enough to venture into the > > > depths yet :) We've actually discussed doing precisely this, for - among other things - this reason. Just nobody stepped up yet to propose the necessary APIs and do the remaining work to use it etc. > > I think that would just push the problem lower. Probably a real > > fix > > would be to somehow propagate > > the tx-status for the specific packet back to the supplicant and > > only > > then it would know that the > > key could be set. That's actually possible today, with the wifi-ack sockopt. It's not really a full solution though I think, there are other issues to solve. We also discussed this at the last workshop, IIRC. > Having userspace track individual packets in the kernel sounds wrong > to me. This also won't help with the packets being received out-of- > order. It would be nice if both the RX and TX ordering was > preserved. Hence my thinking about running PAE over NL80211. It > would then be up to the kernel / drivers to guarantee that the > various packets are ordered appropriately. That's actually not possible, since ordering set_key operations vs. transmitted packets isn't something that's easily done by drivers. However, the solution is far simpler! Once you have nl80211 PAE transport, you can easily even set the key before transmitting the packet and simply indicate that this particular packet should _not_ be encrypted regardless of key presence. johannes
Hi Johannes, > > We've actually discussed doing precisely this, for - among other things > - this reason. Just nobody stepped up yet to propose the necessary APIs > and do the remaining work to use it etc. > Do you have any thoughts on what the operations should look like or do you want me to take a stab in the dark at this? >> Having userspace track individual packets in the kernel sounds wrong >> to me. This also won't help with the packets being received out-of- >> order. It would be nice if both the RX and TX ordering was >> preserved. Hence my thinking about running PAE over NL80211. It >> would then be up to the kernel / drivers to guarantee that the >> various packets are ordered appropriately. > > That's actually not possible, since ordering set_key operations vs. > transmitted packets isn't something that's easily done by drivers. Fair enough, but at least the kernel can do its best to make sure that such races do not manifest themselves out into userspace. E.g. making sure that PAE events arrive after the connect events, etc. > > However, the solution is far simpler! Once you have nl80211 PAE > transport, you can easily even set the key before transmitting the > packet and simply indicate that this particular packet should _not_ be > encrypted regardless of key presence. > Makes sense. Should PAE packets always be sent unencrypted? Or should userspace be notified whether PAE was received unencrypted and send a response with the same flag? Also, while we're on this subject. Should the kernel auto-manage the LINKMODE and OPERSTATE flags? It would seem that it already has the information to do so, and having userspace manage this just introduces another source of latency / possibility of race conditions, etc. Regards, -Denis
On 06/09/2017 12:28 AM, Johannes Berg wrote: > On Thu, 2017-06-08 at 19:07 -0500, Denis Kenzior wrote: > >>>> Fundamentally there is a race between the genl/nl80211 socket to >>>> the >>>> kernel and the PAE socket that handles the authentication >>>> aspects. I >>>> think the only way to >>>> fix this is to make sure that PAE flows over the genl/nl80211 >>>> socket >>>> to preserve the proper order of events. > > Correct. > >>>> However there are lots of >>>> dragons in the kernel >>>> side of this and we haven't been brave enough to venture into the >>>> depths yet :) > > We've actually discussed doing precisely this, for - among other things > - this reason. Just nobody stepped up yet to propose the necessary APIs > and do the remaining work to use it etc. > >>> I think that would just push the problem lower. Probably a real >>> fix >>> would be to somehow propagate >>> the tx-status for the specific packet back to the supplicant and >>> only >>> then it would know that the >>> key could be set. > > That's actually possible today, with the wifi-ack sockopt. It's not > really a full solution though I think, there are other issues to solve. > We also discussed this at the last workshop, IIRC. > >> Having userspace track individual packets in the kernel sounds wrong >> to me. This also won't help with the packets being received out-of- >> order. It would be nice if both the RX and TX ordering was >> preserved. Hence my thinking about running PAE over NL80211. It >> would then be up to the kernel / drivers to guarantee that the >> various packets are ordered appropriately. > > That's actually not possible, since ordering set_key operations vs. > transmitted packets isn't something that's easily done by drivers. > > However, the solution is far simpler! Once you have nl80211 PAE > transport, you can easily even set the key before transmitting the > packet and simply indicate that this particular packet should _not_ be > encrypted regardless of key presence. My ath10k firmware cannot deal with a case like this: pkt is enqueued before key is set key is set pkt is transmitted (incorrectly) This is because of how the tid's header-length variables are set up and modified when the keys are set, and I don't see any good way to fix this. Stock ath10k firmware goes to great lengths to parse EAPOL frames and try to work around it in that manner, but that breaks .11r (or used to, I haven't tried stock firmware lately) and adds more complexity to the code. From a patch someone sent to hostapd list last night, it seems we could get the tx-status for the EAPOL 4/4, and in that case, we *know* the pkt has been transmitted, so we can then set the key safely it would seem? Thanks, Ben
Hi Denis, Btw, now I finally remembered what this also fixes - the whole bridging mess :-) When we have this, we no longer need hostapd/wpas to be aware of bridging and capturing frames beneath the bridge - something that's actually a regression in Linux at some point. > Do you have any thoughts on what the operations should look like or > do you want me to take a stab in the dark at this? Haven't really thought about it that much. I guess it should be similar to mgmt_tx, quite possibly even just using that same operation? Similarly, nl80211_register_mgmt() would have to be extended. We already have NL80211_ATTR_CONTROL_PORT_ETHERTYPE, so perhaps this should be used for some sort of filtering, i.e. perhaps nl80211_register_mgmt() could be used with NL80211_ATTR_CONTROL_PORT or something... Not really sure what the best plan is. Perhaps Jouni has some other ideas. It does seem like this shouldn't allow any other data frames to be intercepted, since the control_port_protocol already requires special handling in mac80211, but we don't really want to add even more than that, i.e. I really don't want to see arbitrary ethertype interception at this level. > > That's actually not possible, since ordering set_key operations vs. > > transmitted packets isn't something that's easily done by drivers. > > Fair enough, but at least the kernel can do its best to make sure > that such races do not manifest themselves out into userspace. E.g. > making sure that PAE events arrive after the connect events, etc. Yes, having the events across a common path would actually solve that particular race - not much more though, afaict. > Makes sense. Should PAE packets always be sent unencrypted? Or > should userspace be notified whether PAE was received unencrypted and > send a response with the same flag? No, they shouldn't always be sent unencrypted. They're specified to be encrypted, e.g. for GTK rekeying that's required (though some non-IEEE protocols require unencrypted, NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT.) Since we don't use the value of this attribute for anything but the TX path, we can go two ways here: 1) with the new EAPOL-over-nl80211, require userspace to set the unencrypted flag for every frame where it's needed, i.e. even for rekeying frames on such non-IEEE protocols 2) if "do not encrypt" isn't specified, use control_port_no_encrypt as the default value I think I'd prefer (1), but only slightly, so perhaps it makes sense to check what's better in the resulting code. > Also, while we're on this subject. Should the kernel auto-manage > the LINKMODE and OPERSTATE flags? It would seem that it already has > the information to do so, and having userspace manage this just > introduces another source of latency / possibility of race > conditions, etc. I'm not convinced that it does have that information in all cases, and I don't see how that causes race conditions or much latency, since for client mode userspace would probably just set that together with the NL80211_STA_FLAG_AUTHORIZED flag? Anyway - that really should be a separate discussion and project, and I'd prefer not to take this thread away from the original subject too much. johannes
On Fri, 2017-06-09 at 06:46 -0700, Ben Greear wrote: > > However, the solution is far simpler! Once you have nl80211 PAE > > transport, you can easily even set the key before transmitting the > > packet and simply indicate that this particular packet should _not_ > > be encrypted regardless of key presence. > > My ath10k firmware cannot deal with a case like this: > > pkt is enqueued before key is set > key is set > pkt is transmitted (incorrectly) > > This is because of how the tid's header-length variables are set up > and modified when the keys are set, and I don't see any good way to > fix this. That seems awful, and anyway will not work with the mentioned non-IEEE protocols that require not encrypting the rekeying frames even when keys have been set up. I don't know what to tell you here, I think it'd be best if you fix that. > Stock ath10k firmware goes to great lengths to parse EAPOL frames and > try to work around it in that manner, but that breaks .11r (or used > to, I haven't tried stock firmware lately) and adds more complexity > to the code. It just has to be a single flag saying "don't encrypt this frame" - nothing super complicated about that? In ath10k it looks like HTT_DATA_TX_DESC_FLAGS0_NO_ENCRYPT gets set for this, seems easy enough? > From a patch someone sent to hostapd list last night, it seems we > could get the tx-status for the EAPOL 4/4, and in that case, we > *know* the pkt has been transmitted, so we can then set the key > safely it would seem? I think so, and I don't remember why we dismissed this solution. Could be that we just decided solving the bridging issue at the same time, while not introducing more latency, was better. Also, the other way can possibly solve some PTK rekeying issues, so overall the solution to go all the way seems better. johannes
On 06/09/2017 01:01 PM, Johannes Berg wrote: > On Fri, 2017-06-09 at 06:46 -0700, Ben Greear wrote: > >>> However, the solution is far simpler! Once you have nl80211 PAE >>> transport, you can easily even set the key before transmitting the >>> packet and simply indicate that this particular packet should _not_ >>> be encrypted regardless of key presence. >> >> My ath10k firmware cannot deal with a case like this: >> >> pkt is enqueued before key is set >> key is set >> pkt is transmitted (incorrectly) >> >> This is because of how the tid's header-length variables are set up >> and modified when the keys are set, and I don't see any good way to >> fix this. > > That seems awful, and anyway will not work with the mentioned non-IEEE > protocols that require not encrypting the rekeying frames even when > keys have been set up. > > I don't know what to tell you here, I think it'd be best if you fix > that. The case that fails is basically any packet that is currently enqueued in the firmware when the key is set is transmitted incorrectly or not at all. And, maybe this is only for DATA tids. Otherwise, the no-encrypt logic should work fine. So, it is just the race with the EAPOL 4/4 and set-key that causes issues as far as I can tell. It looks like the EAPOL 4/4 and set-key race is fixable without too much effort, so I think I will focus on that for now instead of further hacking special case logic into the firmware. >> Stock ath10k firmware goes to great lengths to parse EAPOL frames and >> try to work around it in that manner, but that breaks .11r (or used >> to, I haven't tried stock firmware lately) and adds more complexity >> to the code. > > It just has to be a single flag saying "don't encrypt this frame" - > nothing super complicated about that? > > In ath10k it looks like HTT_DATA_TX_DESC_FLAGS0_NO_ENCRYPT gets set for > this, seems easy enough? > >> From a patch someone sent to hostapd list last night, it seems we >> could get the tx-status for the EAPOL 4/4, and in that case, we >> *know* the pkt has been transmitted, so we can then set the key >> safely it would seem? > > I think so, and I don't remember why we dismissed this solution. Could > be that we just decided solving the bridging issue at the same time, > while not introducing more latency, was better. > > Also, the other way can possibly solve some PTK rekeying issues, so > overall the solution to go all the way seems better. I guess I don't fully understand the PAE thing, but if you all like it, then sounds good to me. For kernels not supporting this new feature, it seems that having supplicant wait for tx-status would be a good interim fix? Thanks, Ben
2017-06-09 22:18 GMT+02:00 Ben Greear <greearb@candelatech.com>: > On 06/09/2017 01:01 PM, Johannes Berg wrote: >> >> On Fri, 2017-06-09 at 06:46 -0700, Ben Greear wrote: >> >>>> However, the solution is far simpler! Once you have nl80211 PAE >>>> transport, you can easily even set the key before transmitting the >>>> packet and simply indicate that this particular packet should _not_ >>>> be encrypted regardless of key presence. >>> >>> >>> My ath10k firmware cannot deal with a case like this: >>> >>> pkt is enqueued before key is set >>> key is set >>> pkt is transmitted (incorrectly) >>> >>> This is because of how the tid's header-length variables are set up >>> and modified when the keys are set, and I don't see any good way to >>> fix this. >> >> >> That seems awful, and anyway will not work with the mentioned non-IEEE >> protocols that require not encrypting the rekeying frames even when >> keys have been set up. >> >> I don't know what to tell you here, I think it'd be best if you fix >> that. > > > The case that fails is basically any packet that is currently > enqueued in the firmware when the key is set is transmitted incorrectly or > not at all. > And, maybe this is only for DATA tids. > > Otherwise, the no-encrypt logic should work fine. So, it is just the race > with the EAPOL 4/4 and set-key that causes issues as far as I can tell. > > It looks like the EAPOL 4/4 and set-key race is fixable without too much > effort, > so I think I will focus on that for now instead of further hacking special > case logic into the firmware. > Ben, as I remember correctly there is a flag, WMI_PEER_NEED_PTK_4_WAY This fix race (you describe) in the firmware/hw. For 636 firmware, where we tested STA mode really hard (5 years ago), that works perfect. So, I am not sure why this flag don't work correctly with your firmware. Regarding EAPOL frames I am not sure you will have real/correct ACK. I remember in case of mgmt frames FW always return ACK - but probably you will check that. I also fight with some EAPOL frames, but forgot why ... Seems my brain removed this information for some reason :-) BR Janusz >>> Stock ath10k firmware goes to great lengths to parse EAPOL frames and >>> try to work around it in that manner, but that breaks .11r (or used >>> to, I haven't tried stock firmware lately) and adds more complexity >>> to the code. >> >> >> It just has to be a single flag saying "don't encrypt this frame" - >> nothing super complicated about that? >> >> In ath10k it looks like HTT_DATA_TX_DESC_FLAGS0_NO_ENCRYPT gets set for >> this, seems easy enough? >> >>> From a patch someone sent to hostapd list last night, it seems we >>> could get the tx-status for the EAPOL 4/4, and in that case, we >>> *know* the pkt has been transmitted, so we can then set the key >>> safely it would seem? >> >> >> I think so, and I don't remember why we dismissed this solution. Could >> be that we just decided solving the bridging issue at the same time, >> while not introducing more latency, was better. >> >> Also, the other way can possibly solve some PTK rekeying issues, so >> overall the solution to go all the way seems better. > > > I guess I don't fully understand the PAE thing, but if you all like it, > then sounds good to me. > > For kernels not supporting this new feature, it seems that having supplicant > wait for tx-status would be a good interim fix? > > Thanks, > Ben > > -- > Ben Greear <greearb@candelatech.com> > Candela Technologies Inc http://www.candelatech.com > > > _______________________________________________ > Hostap mailing list > Hostap@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/hostap
On 06/09/2017 02:47 PM, Janusz Dziedzic wrote: > 2017-06-09 22:18 GMT+02:00 Ben Greear <greearb@candelatech.com>: >> On 06/09/2017 01:01 PM, Johannes Berg wrote: >>> >>> On Fri, 2017-06-09 at 06:46 -0700, Ben Greear wrote: >>> >>>>> However, the solution is far simpler! Once you have nl80211 PAE >>>>> transport, you can easily even set the key before transmitting the >>>>> packet and simply indicate that this particular packet should _not_ >>>>> be encrypted regardless of key presence. >>>> >>>> >>>> My ath10k firmware cannot deal with a case like this: >>>> >>>> pkt is enqueued before key is set >>>> key is set >>>> pkt is transmitted (incorrectly) >>>> >>>> This is because of how the tid's header-length variables are set up >>>> and modified when the keys are set, and I don't see any good way to >>>> fix this. >>> >>> >>> That seems awful, and anyway will not work with the mentioned non-IEEE >>> protocols that require not encrypting the rekeying frames even when >>> keys have been set up. >>> >>> I don't know what to tell you here, I think it'd be best if you fix >>> that. >> >> >> The case that fails is basically any packet that is currently >> enqueued in the firmware when the key is set is transmitted incorrectly or >> not at all. >> And, maybe this is only for DATA tids. >> >> Otherwise, the no-encrypt logic should work fine. So, it is just the race >> with the EAPOL 4/4 and set-key that causes issues as far as I can tell. >> >> It looks like the EAPOL 4/4 and set-key race is fixable without too much >> effort, >> so I think I will focus on that for now instead of further hacking special >> case logic into the firmware. >> > Ben, as I remember correctly there is a flag, > WMI_PEER_NEED_PTK_4_WAY > > This fix race (you describe) in the firmware/hw. > For 636 firmware, where we tested STA mode really hard (5 years ago), > that works perfect. > So, I am not sure why this flag don't work correctly with your firmware. I removed/ignored this flag/logic to make .11r work (in 10.1.4-mumble), just possibly .11r worked before in the 636 firmware. > > Regarding EAPOL frames I am not sure you will have real/correct ACK. I > remember in case of mgmt frames FW always return ACK - but probably > you will check that. I fixed the rx-status, but really, valid or not, it would at least fix the race to wait to get the status. > I also fight with some EAPOL frames, but forgot why ... Seems my brain > removed this information for some reason :-) The firmware code was nasty in this regard...I wouldn't try to remember it if I were you :) Thanks, Ben
On 06/09/2017 04:51 PM, fengbin wrote: > seems your firmware doesn't support HTT_DATA_TX_DESC_FLAGS0_NO_ENCRYPT? > Otherwise , it should work perfectly because Key messages are marked as no hw encryption. Well, it could be my bug.....but unless you have access to ath10k firmware, then I can't explain further what is the particular issue. If you do have access, then I can give you some hints to follow the code path in question. Thanks, Ben
On 09-06-17 22:18, Ben Greear wrote: > On 06/09/2017 01:01 PM, Johannes Berg wrote: >> On Fri, 2017-06-09 at 06:46 -0700, Ben Greear wrote: >> >>>> However, the solution is far simpler! Once you have nl80211 PAE >>>> transport, you can easily even set the key before transmitting the >>>> packet and simply indicate that this particular packet should _not_ >>>> be encrypted regardless of key presence. >>> >>> My ath10k firmware cannot deal with a case like this: >>> >>> pkt is enqueued before key is set >>> key is set >>> pkt is transmitted (incorrectly) >>> >>> This is because of how the tid's header-length variables are set up >>> and modified when the keys are set, and I don't see any good way to >>> fix this. >> >> That seems awful, and anyway will not work with the mentioned non-IEEE >> protocols that require not encrypting the rekeying frames even when >> keys have been set up. >> >> I don't know what to tell you here, I think it'd be best if you fix >> that. > > The case that fails is basically any packet that is currently > enqueued in the firmware when the key is set is transmitted incorrectly > or not at all. > And, maybe this is only for DATA tids. > > Otherwise, the no-encrypt logic should work fine. So, it is just the race > with the EAPOL 4/4 and set-key that causes issues as far as I can tell. > > It looks like the EAPOL 4/4 and set-key race is fixable without too much > effort, > so I think I will focus on that for now instead of further hacking special > case logic into the firmware. > >>> Stock ath10k firmware goes to great lengths to parse EAPOL frames and >>> try to work around it in that manner, but that breaks .11r (or used >>> to, I haven't tried stock firmware lately) and adds more complexity >>> to the code. >> >> It just has to be a single flag saying "don't encrypt this frame" - >> nothing super complicated about that? >> >> In ath10k it looks like HTT_DATA_TX_DESC_FLAGS0_NO_ENCRYPT gets set for >> this, seems easy enough? >> >>> From a patch someone sent to hostapd list last night, it seems we >>> could get the tx-status for the EAPOL 4/4, and in that case, we >>> *know* the pkt has been transmitted, so we can then set the key >>> safely it would seem? >> >> I think so, and I don't remember why we dismissed this solution. Could >> be that we just decided solving the bridging issue at the same time, >> while not introducing more latency, was better. >> >> Also, the other way can possibly solve some PTK rekeying issues, so >> overall the solution to go all the way seems better. > > I guess I don't fully understand the PAE thing, but if you all like it, > then sounds good to me. > > For kernels not supporting this new feature, it seems that having > supplicant > wait for tx-status would be a good interim fix? For what it is worth. In brcmfmac we block setting the PTK when EAPOL frame is in transit exactly for this long-standing issue. So in short this is what we do: in .start_xmit() we (atomically) increase pend_1x count when ether proto is PAE and decrease it when transmit completes (through brcmf_tx_finalize()). As long as pend_1x count is non-zero we block setting the PTK. Regards, Arend
diff --git a/src/rsn_supp/wpa.c b/src/rsn_supp/wpa.c index 8a1d164..50a3006 100644 --- a/src/rsn_supp/wpa.c +++ b/src/rsn_supp/wpa.c @@ -1423,6 +1423,11 @@ static void wpa_supplicant_process_3_of_4(struct wpa_sm *sm, sm->renew_snonce = 1; if (key_info & WPA_KEY_INFO_INSTALL) { + /* Well now...what if the NIC hasn't actually put the 4/4 on the air + * yet? If we set the key too soon, it is liable to corrupt the pkt being + * sent.. I don't know a good fix, but here is a hack. + */ + os_sleep(0, 10000); /* sleep 10ms */ if (wpa_supplicant_install_ptk(sm, key)) goto failed; }