@@ -42,6 +42,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
rk3288-veyron-minnie.dtb \
rk3328-evb.dtb \
rk3368-geekbox.dtb \
+ rk3368-sheep.dtb \
rk3368-px5-evb.dtb \
rk3399-evb.dtb \
rk3399-puma.dtb \
new file mode 100644
@@ -0,0 +1,283 @@
+/*
+ * (C) Copyright 2016 Rockchip Electronics Co., Ltd
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/dts-v1/;
+#include "rk3368.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Rockchip sheep board";
+ compatible = "rockchip,sheep", "rockchip,rk3368";
+
+ chosen {
+ stdout-path = "serial3:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+
+ ext_gmac: gmac-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <125000000>;
+ clock-output-names = "ext_gmac";
+ #clock-cells = <0>;
+ };
+
+ ir: ir-receiver {
+ compatible = "gpio-ir-receiver";
+ gpios = <&gpio3 30 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_int>;
+ };
+
+ keys: gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwr_key>;
+
+ power {
+ gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
+ label = "GPIO Power";
+ linux,code = <KEY_POWER>;
+ wakeup-source;
+ };
+ };
+
+ leds: gpio-leds {
+ compatible = "gpio-leds";
+
+ blue {
+ gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+ label = "geekbox:blue:led";
+ default-state = "on";
+ };
+
+ red {
+ gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+ label = "geekbox:red:led";
+ default-state = "off";
+ };
+ };
+
+ vcc_sys: vcc-sys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sys";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+};
+
+&emmc {
+ status = "okay";
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ clock-frequency = <150000000>;
+ disable-wp;
+ keep-power-in-suspend;
+ non-removable;
+ num-slots = <1>;
+ vmmc-supply = <&vcc_io>;
+ vqmmc-supply = <&vcc18_flash>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_bus8>;
+};
+
+&gmac {
+ status = "okay";
+ phy-supply = <&vcc_lan>;
+ phy-mode = "rgmii";
+ clock_in_out = "input";
+ assigned-clocks = <&cru SCLK_MAC>;
+ assigned-clock-parents = <&ext_gmac>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ tx_delay = <0x30>;
+ rx_delay = <0x10>;
+};
+
+&i2c0 {
+ status = "okay";
+
+ rk808: pmic@1b {
+ compatible = "rockchip,rk808";
+ reg = <0x1b>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int>, <&pmic_sleep>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+ rockchip,system-power-controller;
+ vcc1-supply = <&vcc_sys>;
+ vcc2-supply = <&vcc_sys>;
+ vcc3-supply = <&vcc_sys>;
+ vcc4-supply = <&vcc_sys>;
+ vcc6-supply = <&vcc_sys>;
+ vcc7-supply = <&vcc_sys>;
+ vcc8-supply = <&vcc_io>;
+ vcc9-supply = <&vcc_sys>;
+ vcc10-supply = <&vcc_sys>;
+ vcc11-supply = <&vcc_sys>;
+ vcc12-supply = <&vcc_io>;
+ clock-output-names = "xin32k", "rk808-clkout2";
+ #clock-cells = <1>;
+
+ regulators {
+ vdd_cpu: DCDC_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vdd_cpu";
+ };
+
+ vdd_log: DCDC_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vdd_log";
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc_ddr";
+ };
+
+ vcc_io: DCDC_REG4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc_io";
+ };
+
+ vcc18_flash: LDO_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc18_flash";
+ };
+
+ vcc33_lcd: LDO_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc33_lcd";
+ };
+
+ vdd_10: LDO_REG3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-name = "vdd_10";
+ };
+
+ vcca_18: LDO_REG4 {
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcca_18";
+ };
+
+ vccio_sd: LDO_REG5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio_sd";
+ };
+
+ vdd10_lcd: LDO_REG6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-name = "vdd10_lcd";
+ };
+
+ vcc_18: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc_18";
+ };
+
+ vcc18_lcd: LDO_REG8 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc18_lcd";
+ };
+
+ vcc_sd: SWITCH_REG1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc_sd";
+ };
+
+ vcc_lan: SWITCH_REG2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vcc_lan";
+ };
+ };
+ };
+};
+
+&pinctrl {
+ ir {
+ ir_int: ir-int {
+ rockchip,pins = <3 30 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ keys {
+ pwr_key: pwr-key {
+ rockchip,pins = <0 2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_sleep: pmic-sleep {
+ rockchip,pins = <0 0 RK_FUNC_2 &pcfg_pull_none>;
+ };
+
+ pmic_int: pmic-int {
+ rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+};
+
+&tsadc {
+ status = "okay";
+ rockchip,hw-tshut-mode = <0>; /* CRU */
+ rockchip,hw-tshut-polarity = <1>; /* high */
+};
+
+&uart4 {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_otg {
+ status = "okay";
+};
+
+&wdt {
+ status = "okay";
+};
@@ -6,6 +6,12 @@ choice
config TARGET_GEEKBOX
bool "GeekBox"
+config TARGET_SHEEP
+ bool "Sheep board"
+ help
+ Sheep board is designed by Rockchip as a EVB board
+ for rk3368.
+
config TARGET_EVB_PX5
bool "Evb-PX5"
help
@@ -23,6 +29,6 @@ config SYS_MALLOC_F_LEN
default 0x0800
source "board/geekbuying/geekbox/Kconfig"
+source "board/rockchip/sheep_rk3368/Kconfig"
source "board/rockchip/evb_px5/Kconfig"
-
endif
new file mode 100644
@@ -0,0 +1,15 @@
+if TARGET_SHEEP
+
+config SYS_BOARD
+ default "sheep_rk3368"
+
+config SYS_VENDOR
+ default "rockchip"
+
+config SYS_CONFIG_NAME
+ default "sheep_rk3368"
+
+config BOARD_SPECIFIC_OPTIONS # dummy
+ def_bool y
+
+endif
new file mode 100644
@@ -0,0 +1,6 @@
+PX5 EVB
+M: Andy Yan <andy.yan@rock-chips.com>
+S: Maintained
+F: board/rockchip/sheep_rk3368
+F: include/configs/sheep_rk3368.h
+F: configs/sheep-rk3368_defconfig
new file mode 100644
@@ -0,0 +1,7 @@
+#
+# Copyright (c) 2017 Rockchip Electronics Co., Ltd
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += sheep_rk3368.o
new file mode 100644
@@ -0,0 +1,37 @@
+/*
+ * Copyright (c) 2017 Andy Yan
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/grf_rk3368.h>
+#include <syscon.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int mach_cpu_init(void)
+{
+ return 0;
+}
+
+int board_init(void)
+{
+ return 0;
+}
+
+int dram_init(void)
+{
+ gd->ram_size = 0x80000000;
+
+ return 0;
+}
+
+int dram_init_banksize(void)
+{
+ gd->bd->bi_dram[0].start = 0x200000;
+ gd->bd->bi_dram[0].size = 0x7fe00000;
+
+ return 0;
+}
new file mode 100644
@@ -0,0 +1,28 @@
+CONFIG_ARM=y
+CONFIG_ARCH_ROCKCHIP=y
+CONFIG_ROCKCHIP_RK3368=y
+CONFIG_TARGET_SHEEP=y
+CONFIG_DEFAULT_DEVICE_TREE="rk3368-sheep"
+CONFIG_HUSH_PARSER=y
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_FASTBOOT=y
+CONFIG_ANDROID_BOOT_IMAGE=y
+# CONFIG_CMD_IMLS is not set
+CONFIG_REGMAP=y
+CONFIG_SYSCON=y
+CONFIG_CLK=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_BOOTRK=y
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_ROCKCHIP=y
+CONFIG_SYSRESET=y
+CONFIG_PINCTRL=y
+CONFIG_ROCKCHIP_RK3368_PINCTRL=y
+CONFIG_RAM=y
+CONFIG_DEBUG_UART=y
+CONFIG_DEBUG_UART_BASE=0xFF1b0000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_DEBUG_UART_SKIP_INIT=y
+CONFIG_ERRNO_STR=y
new file mode 100644
@@ -0,0 +1,22 @@
+/*
+ * Copyright (c) 2017 Rockchip Electronics Co., Ltd
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIGS_PX5_EVB_H
+#define __CONFIGS_PX5_EVB_H
+
+#include <configs/rk3368_common.h>
+
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define KERNEL_LOAD_ADDR 0x280000
+#define DTB_LOAD_ADDR 0x5600000
+#define INITRD_LOAD_ADDR 0x5bf0000
+#define CONFIG_ENV_IS_NOWHERE
+#define CONFIG_ENV_SIZE 0x2000
+
+#define CONFIG_SYS_WHITE_ON_BLACK
+#define CONFIG_CONSOLE_SCROLL_LINES 10
+
+#endif
Sheep board is designed by Rockchip as a EVB for rk3368. Currently it is able to boot a linux kernel and system to console with the miniloader run as fist level loader. Signed-off-by: Andy Yan <andy.yan@rock-chips.com> --- arch/arm/dts/Makefile | 1 + arch/arm/dts/rk3368-sheep.dts | 283 +++++++++++++++++++++++++++++ arch/arm/mach-rockchip/rk3368/Kconfig | 8 +- board/rockchip/sheep_rk3368/Kconfig | 15 ++ board/rockchip/sheep_rk3368/MAINTAINERS | 6 + board/rockchip/sheep_rk3368/Makefile | 7 + board/rockchip/sheep_rk3368/sheep_rk3368.c | 37 ++++ configs/sheep-rk3368_defconfig | 28 +++ include/configs/sheep_rk3368.h | 22 +++ 9 files changed, 406 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/rk3368-sheep.dts create mode 100644 board/rockchip/sheep_rk3368/Kconfig create mode 100644 board/rockchip/sheep_rk3368/MAINTAINERS create mode 100644 board/rockchip/sheep_rk3368/Makefile create mode 100644 board/rockchip/sheep_rk3368/sheep_rk3368.c create mode 100644 configs/sheep-rk3368_defconfig create mode 100644 include/configs/sheep_rk3368.h