Message ID | 20161110051857.6547-1-vigneshr@ti.com |
---|---|
State | Superseded |
Delegated to: | Jagannadha Sutradharudu Teki |
Headers | show |
On 11/10/2016 06:18 AM, Vignesh R wrote: > According to Section 11.15.4.9.2 Indirect Write Controller of K2G SoC > TRM SPRUHY8D[1], the external master is only permitted to issue 32-bit > data interface writes until the last word of an indirect transfer > otherwise indirect writes is known to fails sometimes. So, make sure > that QSPI indirect writes are 32 bit sized except for the last write. > > [1]www.ti.com/lit/ug/spruhy8d/spruhy8d.pdf > > Signed-off-by: Vignesh R <vigneshr@ti.com> I would if it wouldn't be better to use bounce buffer for the txbuf . See common/bouncebuf.c > --- > drivers/spi/cadence_qspi_apb.c | 41 +++++++++++++++++++++++++++++++---------- > 1 file changed, 31 insertions(+), 10 deletions(-) > > diff --git a/drivers/spi/cadence_qspi_apb.c b/drivers/spi/cadence_qspi_apb.c > index e285d3c1e761..0115700ef6a7 100644 > --- a/drivers/spi/cadence_qspi_apb.c > +++ b/drivers/spi/cadence_qspi_apb.c > @@ -739,23 +739,44 @@ int cadence_qspi_apb_indirect_write_execute(struct cadence_spi_platdata *plat, > { > unsigned int page_size = plat->page_size; > unsigned int remaining = n_tx; > - unsigned int write_bytes; > + unsigned int write_bytes = 0; > int ret; > > + /* Handle non-4-byte aligned access to avoid data abort. */ > + if ((uintptr_t) txbuf % 4) { > + write_bytes = n_tx > 3 ? 4 - ((uintptr_t)txbuf % 4) : n_tx; > + /* Configure the indirect read transfer bytes */ > + writel(write_bytes, plat->regbase + CQSPI_REG_INDIRECTWRBYTES); > + /* Start the indirect write transfer */ > + writel(CQSPI_REG_INDIRECTWR_START_MASK, > + plat->regbase + CQSPI_REG_INDIRECTWR); > + writesb(plat->ahbbase, txbuf, write_bytes); > + txbuf += write_bytes; > + remaining -= write_bytes; > + if (remaining > 0) { > + u32 start_addr = readl(plat->regbase + > + CQSPI_REG_INDIRECTWRSTARTADDR); > + start_addr += write_bytes; > + writel(start_addr, plat->regbase + > + CQSPI_REG_INDIRECTWRSTARTADDR); > + } > + } > + > /* Configure the indirect read transfer bytes */ > - writel(n_tx, plat->regbase + CQSPI_REG_INDIRECTWRBYTES); > + writel(n_tx - write_bytes, plat->regbase + CQSPI_REG_INDIRECTWRBYTES); > > - /* Start the indirect write transfer */ > - writel(CQSPI_REG_INDIRECTWR_START_MASK, > - plat->regbase + CQSPI_REG_INDIRECTWR); > + if (remaining > 0) > + writel(CQSPI_REG_INDIRECTWR_START_MASK, > + plat->regbase + CQSPI_REG_INDIRECTWR); > > while (remaining > 0) { > write_bytes = remaining > page_size ? page_size : remaining; > - /* Handle non-4-byte aligned access to avoid data abort. */ > - if (((uintptr_t)txbuf % 4) || (write_bytes % 4)) > - writesb(plat->ahbbase, txbuf, write_bytes); > - else > - writesl(plat->ahbbase, txbuf, write_bytes >> 2); > + > + writesl(plat->ahbbase, txbuf, write_bytes >> 2); > + if (write_bytes % 4) > + writesb(plat->ahbbase, > + txbuf + rounddown(write_bytes, 4), > + write_bytes % 4); > > ret = wait_for_bit("QSPI", plat->regbase + CQSPI_REG_SDRAMLEVEL, > CQSPI_REG_SDRAMLEVEL_WR_MASK << >
On Sunday 13 November 2016 03:13 AM, Marek Vasut wrote: > On 11/10/2016 06:18 AM, Vignesh R wrote: >> According to Section 11.15.4.9.2 Indirect Write Controller of K2G SoC >> TRM SPRUHY8D[1], the external master is only permitted to issue 32-bit >> data interface writes until the last word of an indirect transfer >> otherwise indirect writes is known to fails sometimes. So, make sure >> that QSPI indirect writes are 32 bit sized except for the last write. >> >> [1]www.ti.com/lit/ug/spruhy8d/spruhy8d.pdf >> >> Signed-off-by: Vignesh R <vigneshr@ti.com> > > I would if it wouldn't be better to use bounce buffer for the txbuf . > See common/bouncebuf.c > Yeah, I guess that will also help in implementing DMA support. How about having a generic implementation of bounce buffer support in spi_flash_cmd_{read/write}_ops?
On 11/15/2016 06:03 AM, Vignesh R wrote: > > > On Sunday 13 November 2016 03:13 AM, Marek Vasut wrote: >> On 11/10/2016 06:18 AM, Vignesh R wrote: >>> According to Section 11.15.4.9.2 Indirect Write Controller of K2G SoC >>> TRM SPRUHY8D[1], the external master is only permitted to issue 32-bit >>> data interface writes until the last word of an indirect transfer >>> otherwise indirect writes is known to fails sometimes. So, make sure >>> that QSPI indirect writes are 32 bit sized except for the last write. >>> >>> [1]www.ti.com/lit/ug/spruhy8d/spruhy8d.pdf >>> >>> Signed-off-by: Vignesh R <vigneshr@ti.com> >> >> I would if it wouldn't be better to use bounce buffer for the txbuf . >> See common/bouncebuf.c >> > > Yeah, I guess that will also help in implementing DMA support. How about > having a generic implementation of bounce buffer support in > spi_flash_cmd_{read/write}_ops? We have generic implementation of bounce buffer in common/bouncebuf.c and not everyone needs it.
diff --git a/drivers/spi/cadence_qspi_apb.c b/drivers/spi/cadence_qspi_apb.c index e285d3c1e761..0115700ef6a7 100644 --- a/drivers/spi/cadence_qspi_apb.c +++ b/drivers/spi/cadence_qspi_apb.c @@ -739,23 +739,44 @@ int cadence_qspi_apb_indirect_write_execute(struct cadence_spi_platdata *plat, { unsigned int page_size = plat->page_size; unsigned int remaining = n_tx; - unsigned int write_bytes; + unsigned int write_bytes = 0; int ret; + /* Handle non-4-byte aligned access to avoid data abort. */ + if ((uintptr_t) txbuf % 4) { + write_bytes = n_tx > 3 ? 4 - ((uintptr_t)txbuf % 4) : n_tx; + /* Configure the indirect read transfer bytes */ + writel(write_bytes, plat->regbase + CQSPI_REG_INDIRECTWRBYTES); + /* Start the indirect write transfer */ + writel(CQSPI_REG_INDIRECTWR_START_MASK, + plat->regbase + CQSPI_REG_INDIRECTWR); + writesb(plat->ahbbase, txbuf, write_bytes); + txbuf += write_bytes; + remaining -= write_bytes; + if (remaining > 0) { + u32 start_addr = readl(plat->regbase + + CQSPI_REG_INDIRECTWRSTARTADDR); + start_addr += write_bytes; + writel(start_addr, plat->regbase + + CQSPI_REG_INDIRECTWRSTARTADDR); + } + } + /* Configure the indirect read transfer bytes */ - writel(n_tx, plat->regbase + CQSPI_REG_INDIRECTWRBYTES); + writel(n_tx - write_bytes, plat->regbase + CQSPI_REG_INDIRECTWRBYTES); - /* Start the indirect write transfer */ - writel(CQSPI_REG_INDIRECTWR_START_MASK, - plat->regbase + CQSPI_REG_INDIRECTWR); + if (remaining > 0) + writel(CQSPI_REG_INDIRECTWR_START_MASK, + plat->regbase + CQSPI_REG_INDIRECTWR); while (remaining > 0) { write_bytes = remaining > page_size ? page_size : remaining; - /* Handle non-4-byte aligned access to avoid data abort. */ - if (((uintptr_t)txbuf % 4) || (write_bytes % 4)) - writesb(plat->ahbbase, txbuf, write_bytes); - else - writesl(plat->ahbbase, txbuf, write_bytes >> 2); + + writesl(plat->ahbbase, txbuf, write_bytes >> 2); + if (write_bytes % 4) + writesb(plat->ahbbase, + txbuf + rounddown(write_bytes, 4), + write_bytes % 4); ret = wait_for_bit("QSPI", plat->regbase + CQSPI_REG_SDRAMLEVEL, CQSPI_REG_SDRAMLEVEL_WR_MASK <<
According to Section 11.15.4.9.2 Indirect Write Controller of K2G SoC TRM SPRUHY8D[1], the external master is only permitted to issue 32-bit data interface writes until the last word of an indirect transfer otherwise indirect writes is known to fails sometimes. So, make sure that QSPI indirect writes are 32 bit sized except for the last write. [1]www.ti.com/lit/ug/spruhy8d/spruhy8d.pdf Signed-off-by: Vignesh R <vigneshr@ti.com> --- drivers/spi/cadence_qspi_apb.c | 41 +++++++++++++++++++++++++++++++---------- 1 file changed, 31 insertions(+), 10 deletions(-)