| Message ID | 1445895161-2317-8-git-send-email-o.schinagl@ultimaker.com |
|---|---|
| State | Deferred |
| Headers | show |
On Mon, Oct 26, 2015 at 4:32 PM, Olliver Schinagl <o.schinagl@ultimaker.com> wrote: > From: Olliver Schinagl <oliver@schinagl.nl> > > This patch adds a bit-banging gpio PWM driver. It makes use of hrtimers, > to allow nano-second resolution, though it obviously strongly depends on > the switching speed of the gpio pins, hrtimer and system load. > > Each pwm node can have 1 or more "pwm-gpio" entries, which will be > treated as pwm's as part of a pwm chip. > > Signed-off-by: Olliver Schinagl <oliver@schinagl.nl> > --- > Documentation/devicetree/bindings/pwm/pwm-gpio.txt | 18 ++ > MAINTAINERS | 5 + > drivers/pwm/Kconfig | 15 ++ > drivers/pwm/Makefile | 1 + > drivers/pwm/pwm-gpio.c | 253 +++++++++++++++++++++ > 5 files changed, 292 insertions(+) > create mode 100644 Documentation/devicetree/bindings/pwm/pwm-gpio.txt > create mode 100644 drivers/pwm/pwm-gpio.c > > diff --git a/Documentation/devicetree/bindings/pwm/pwm-gpio.txt b/Documentation/devicetree/bindings/pwm/pwm-gpio.txt > new file mode 100644 > index 0000000..336f61f > --- /dev/null > +++ b/Documentation/devicetree/bindings/pwm/pwm-gpio.txt > @@ -0,0 +1,18 @@ > +Generic GPIO bit-banged PWM driver > + > +Required properties: > + - compatible: should be "pwm-gpio" > + - #pwm-cells: should be 3, see pwm.txt in this directory for a general > + description of the cells format. > + - pwm-gpios: one or more gpios describing the used gpio, see the gpio > + bindings for the used gpio driver. I'm not sure there is really much advantage to having multiple gpios per node. It would simplify the driver a bit not to, but I don't feel strongly either way. > + > +Example: > +#include <dt-bindings/gpio/gpio.h> > + > + pwm: pwm@0 { Unit address should be associated with a reg property, so drop it. > + compatible = "pwm-gpio"; > + #pwm-cells = 3; > + pwm-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; > + pwm-gpios = <&pio 7 2 GPIO_ACTIVE_LOW>; This would not actually compile. You can't have 2 properties of the same name. > + }; > diff --git a/MAINTAINERS b/MAINTAINERS > index 7ba7ab7..0ae7fbf 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -4555,6 +4555,11 @@ F: drivers/i2c/muxes/i2c-mux-gpio.c > F: include/linux/i2c-mux-gpio.h > F: Documentation/i2c/muxes/i2c-mux-gpio > > +GENERIC GPIO PWM DRIVER > +M: Olliver Schinagl <oliver@schinagl.nl> > +S: Maintained > +F: drivers/pwm/pwm-gpio.c Can you add the binding doc too. Rob -- To unsubscribe from this list: send the line "unsubscribe linux-pwm" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hey Rob, On October 27, 2015 8:42:48 AM CET, Rob Herring <robh+dt@kernel.org> wrote: >On Mon, Oct 26, 2015 at 4:32 PM, Olliver Schinagl ><o.schinagl@ultimaker.com> wrote: >> From: Olliver Schinagl <oliver@schinagl.nl> >> >> This patch adds a bit-banging gpio PWM driver. It makes use of >hrtimers, >> to allow nano-second resolution, though it obviously strongly depends >on >> the switching speed of the gpio pins, hrtimer and system load. >> >> Each pwm node can have 1 or more "pwm-gpio" entries, which will be >> treated as pwm's as part of a pwm chip. >> >> Signed-off-by: Olliver Schinagl <oliver@schinagl.nl> >> --- >> Documentation/devicetree/bindings/pwm/pwm-gpio.txt | 18 ++ >> MAINTAINERS | 5 + >> drivers/pwm/Kconfig | 15 ++ >> drivers/pwm/Makefile | 1 + >> drivers/pwm/pwm-gpio.c | 253 >+++++++++++++++++++++ >> 5 files changed, 292 insertions(+) >> create mode 100644 >Documentation/devicetree/bindings/pwm/pwm-gpio.txt >> create mode 100644 drivers/pwm/pwm-gpio.c >> >> diff --git a/Documentation/devicetree/bindings/pwm/pwm-gpio.txt >b/Documentation/devicetree/bindings/pwm/pwm-gpio.txt >> new file mode 100644 >> index 0000000..336f61f >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/pwm/pwm-gpio.txt >> @@ -0,0 +1,18 @@ >> +Generic GPIO bit-banged PWM driver >> + >> +Required properties: >> + - compatible: should be "pwm-gpio" >> + - #pwm-cells: should be 3, see pwm.txt in this directory for a >general >> + description of the cells format. >> + - pwm-gpios: one or more gpios describing the used gpio, see the >gpio >> + bindings for the used gpio driver. > >I'm not sure there is really much advantage to having multiple gpios >per node. It would simplify the driver a bit not to, but I don't feel >strongly either way. I figured this way you have one (or more) gpio 'chips' and then per chip 1 or more outputs. I actually thing pne would use several gpios rather then several 'chips'. Most hardware oprates the same way i thought. > >> + >> +Example: >> +#include <dt-bindings/gpio/gpio.h> >> + >> + pwm: pwm@0 { > >Unit address should be associated with a reg property, so drop it. Done > >> + compatible = "pwm-gpio"; >> + #pwm-cells = 3; >> + pwm-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; >> + pwm-gpios = <&pio 7 2 GPIO_ACTIVE_LOW>; > >This would not actually compile. You can't have 2 properties of the >same name. A bad example is still a bug. Fixed. > >> + }; >> diff --git a/MAINTAINERS b/MAINTAINERS >> index 7ba7ab7..0ae7fbf 100644 >> --- a/MAINTAINERS >> +++ b/MAINTAINERS >> @@ -4555,6 +4555,11 @@ F: drivers/i2c/muxes/i2c-mux-gpio.c >> F: include/linux/i2c-mux-gpio.h >> F: Documentation/i2c/muxes/i2c-mux-gpio >> >> +GENERIC GPIO PWM DRIVER >> +M: Olliver Schinagl <oliver@schinagl.nl> >> +S: Maintained >> +F: drivers/pwm/pwm-gpio.c > >Can you add the binding doc too. Sure, done. > >Rob
On Mon, Oct 26, 2015 at 10:32:38PM +0100, Olliver Schinagl wrote: > From: Olliver Schinagl <oliver@schinagl.nl> > > This patch adds a bit-banging gpio PWM driver. It makes use of hrtimers, > to allow nano-second resolution, though it obviously strongly depends on > the switching speed of the gpio pins, hrtimer and system load. > > Each pwm node can have 1 or more "pwm-gpio" entries, which will be > treated as pwm's as part of a pwm chip. > > Signed-off-by: Olliver Schinagl <oliver@schinagl.nl> > --- > Documentation/devicetree/bindings/pwm/pwm-gpio.txt | 18 ++ > MAINTAINERS | 5 + > drivers/pwm/Kconfig | 15 ++ > drivers/pwm/Makefile | 1 + > drivers/pwm/pwm-gpio.c | 253 +++++++++++++++++++++ > 5 files changed, 292 insertions(+) > create mode 100644 Documentation/devicetree/bindings/pwm/pwm-gpio.txt > create mode 100644 drivers/pwm/pwm-gpio.c > > diff --git a/Documentation/devicetree/bindings/pwm/pwm-gpio.txt b/Documentation/devicetree/bindings/pwm/pwm-gpio.txt > new file mode 100644 > index 0000000..336f61f > --- /dev/null > +++ b/Documentation/devicetree/bindings/pwm/pwm-gpio.txt > @@ -0,0 +1,18 @@ > +Generic GPIO bit-banged PWM driver > + > +Required properties: > + - compatible: should be "pwm-gpio" > + - #pwm-cells: should be 3, see pwm.txt in this directory for a general > + description of the cells format. > + - pwm-gpios: one or more gpios describing the used gpio, see the gpio > + bindings for the used gpio driver. I agree with Rob that a single GPIO per PWM chip would be more straightforward here. Having multiple GPIOs per chip, and hence a multi-channel chip, suggests that they are in some fashion grouped whereas in reality they are really completely separate. > +Example: > +#include <dt-bindings/gpio/gpio.h> > + > + pwm: pwm@0 { > + compatible = "pwm-gpio"; > + #pwm-cells = 3; I think the correct syntax for this would be: #pwm-cells = <3>; > diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig > index 0cfaf6b..c0bc296 100644 > --- a/drivers/pwm/Kconfig > +++ b/drivers/pwm/Kconfig > @@ -170,6 +170,21 @@ config PWM_IMG > To compile this driver as a module, choose M here: the module > will be called pwm-img > > +config PWM_GPIO > + tristate "Generic GPIO bit-banged PWM driver" > + depends on OF > + depends on GPIOLIB > + help > + Some platforms do not offer any hardware PWM capabilities but do have > + General Purpose Input Output (GPIO) pins available. Using the kernels > + High-Resolution Timer API this driver tries to toggle GPIO using the > + generic kernel PWM framework. The maximum frequency and/or accuracy > + is dependent on several factors such as system load and the maximum > + speed a pin can be toggled at the hardware. > + > + To compile this driver as a module, choose M here: the module > + will be called pwm-gpio. > + This is oddly sorted. Entries should be ordered alphabetically. > config PWM_IMX > tristate "i.MX PWM support" > depends on ARCH_MXC > diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile > index 69b8275..96aa9aa 100644 > --- a/drivers/pwm/Makefile > +++ b/drivers/pwm/Makefile > @@ -13,6 +13,7 @@ obj-$(CONFIG_PWM_CLPS711X) += pwm-clps711x.o > obj-$(CONFIG_PWM_CRC) += pwm-crc.o > obj-$(CONFIG_PWM_EP93XX) += pwm-ep93xx.o > obj-$(CONFIG_PWM_FSL_FTM) += pwm-fsl-ftm.o > +obj-$(CONFIG_PWM_GPIO) += pwm-gpio.o > obj-$(CONFIG_PWM_IMG) += pwm-img.o > obj-$(CONFIG_PWM_IMX) += pwm-imx.o > obj-$(CONFIG_PWM_JZ4740) += pwm-jz4740.o The ordering is correct here. Perhaps just something that got introduced by oversight in a rebase? > diff --git a/drivers/pwm/pwm-gpio.c b/drivers/pwm/pwm-gpio.c > new file mode 100644 > index 0000000..8b588fb > --- /dev/null > +++ b/drivers/pwm/pwm-gpio.c > @@ -0,0 +1,253 @@ > +/* > + * Copyright (c) 2015 Olliver Schinagl <oliver@schinagl.nl> > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; either version 2 of the License, or > + * (at your option) any later version. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + * This driver adds a high-resolution timer based PWM driver. Since this is a > + * bit-banged driver, accuracy will always depend on a lot of factors, such as > + * GPIO toggle speed and system load. I'm not sure this is helpful. The Kconfig snippet already has this information. > + */ > + > +#include <linux/mod_devicetable.h> > +#include <linux/module.h> > +#include <linux/gpio/consumer.h> > +#include <linux/of.h> > +#include <linux/of_gpio.h> > +#include <linux/property.h> > +#include <linux/pwm.h> > +#include <linux/errno.h> > +#include <linux/err.h> > +#include <linux/device.h> > +#include <linux/hrtimer.h> > +#include <linux/ktime.h> > +#include <linux/kernel.h> > +#include <linux/platform_device.h> Please keep these sorted alphabetically. > + > +#define DRV_NAME "pwm-gpio" You only have two locations where you use this and it's going to be ABI immediately, hence you will never be able to change it anyway. So there is really no need for this define. > + > +struct gpio_pwm_data { In my opinion the _data suffix here is redundant. > + struct hrtimer timer; > + struct gpio_desc *gpiod; > + bool polarity; I think this should probably be called "invert" judging by how it's used. > + bool pin_on; > + int on_time; > + int off_time; These can probably be unsigned. > + bool run; How is this different from pwm_is_enabled()? > +}; > + > +struct gpio_pwm_chip { > + struct pwm_chip chip; > +}; If you restrict the driver to a single PWM channel you can merge the gpio_pwm_data structure into this and vastly simplify the management of resources. > + > +static void gpio_pwm_off(struct gpio_pwm_data *gpio_data) > +{ > + gpiod_set_value_cansleep(gpio_data->gpiod, gpio_data->polarity ? 0 : 1); > +} > + > +static void gpio_pwm_on(struct gpio_pwm_data *gpio_data) > +{ > + gpiod_set_value_cansleep(gpio_data->gpiod, gpio_data->polarity ? 1 : 0); > +} According to this, polarity == true means that polarity is normal. > +static int gpio_pwm_set_polarity(struct pwm_chip *chip, struct pwm_device *pwm, > + enum pwm_polarity polarity) > +{ > + struct gpio_pwm_data *gpio_data = pwm_get_chip_data(pwm); > + > + gpio_data->polarity = (polarity != PWM_POLARITY_NORMAL) ? true : false; > + > + return 0; > +} But here polarity == true only if the PWM is configured for inverse polarity. > +static int gpio_pwm_probe(struct platform_device *pdev) > +{ > + int ret; > + struct gpio_pwm_chip *gpio_chip; > + int npwm, i; i can be unsigned int. > + int hrtimer = 0; This can be unsigned int. > + > + npwm = of_gpio_named_count(pdev->dev.of_node, "pwm-gpios"); > + if (npwm < 1) > + return -ENODEV; Don't you want to propagate error codes from of_gpio_named_count()? So this should probably be: if (npwm < 0) return npwm; if (npwm < 1) return -ENODEV; > + > + gpio_chip = devm_kzalloc(&pdev->dev, sizeof(*gpio_chip), GFP_KERNEL); > + if (!gpio_chip) > + return -ENOMEM; > + > + gpio_chip->chip.dev = &pdev->dev; > + gpio_chip->chip.ops = &gpio_pwm_ops; > + gpio_chip->chip.base = -1; > + gpio_chip->chip.npwm = npwm; > + gpio_chip->chip.of_xlate = of_pwm_xlate_with_flags; > + gpio_chip->chip.of_pwm_n_cells = 3; > + gpio_chip->chip.can_sleep = true; > + > + ret = pwmchip_add(&gpio_chip->chip); > + if (ret < 0) { > + dev_err(&pdev->dev, "failed to add PWM chip: %d\n", ret); > + return ret; > + } You should call pwmchip_add() as late as possible. The pwmchip_add() will register the device with sysfs and hence make it available to userspace. Userspace may immediately start using it, but the below can easily lead to the device going away shortly after it was made available. > + for (i = 0; i < npwm; i++) { > + struct gpio_desc *gpiod; > + struct gpio_pwm_data *gpio_data; > + > + gpiod = devm_gpiod_get_index(&pdev->dev, "pwm", i, > + GPIOD_OUT_LOW); > + if (IS_ERR(gpiod)) { > + int error; > + > + error = PTR_ERR(gpiod); > + if (error != -EPROBE_DEFER) > + dev_err(&pdev->dev, > + "failed to get gpio flags, error: %d\n", > + error); > + return error; > + } > + > + gpio_data = devm_kzalloc(&pdev->dev, sizeof(*gpio_data), > + GFP_KERNEL); > + > + hrtimer_init(&gpio_data->timer, > + CLOCK_MONOTONIC, HRTIMER_MODE_REL); > + gpio_data->timer.function = &gpio_pwm_timer; > + gpio_data->gpiod = gpiod; > + gpio_data->pin_on = false; > + gpio_data->run = false; > + > + if (hrtimer_is_hres_active(&gpio_data->timer)) > + hrtimer++; > + > + pwm_set_chip_data(&gpio_chip->chip.pwms[i], gpio_data); > + } It seems that the only reason why you need to call pwmchip_add() early is so that the PWMs are allocated when you initialize them here. That's easily avoided if you opt for a single PWM per chip, since you can simply manage the resources as part of the chip rather than relying on the per-PWM chip data. > + if (!hrtimer) > + dev_warn(&pdev->dev, "unable to use High-Resolution timer,"); > + dev_warn(&pdev->dev, "%s is restricted to low resolution.", > + DRV_NAME); You'll need curly braces around these two statements, otherwise you'll always show the second part of the warning. Also in the above there is no newline. It's also not going to produce the desired output, even if you use curly braces because dev_warn() will cause KERN_WARNING prefix to be output and mess up the output. You'd want pr_cont() here, but I don't think that's necessary. Perhaps shorten this to something like: if (!hrtimer) dev_warn(&pdev->dev, "HR timer unavailable, restricting to " "low resolution\n"); Also there's no need to include DRV_NAME in the message since it's already part of the prefix added by dev_warn(). > + platform_set_drvdata(pdev, gpio_chip); > + > + dev_info(&pdev->dev, "%d gpio pwms loaded\n", npwm); Please either drop this or make it debug level. No need to brag about success. We're interested in seeing error messages. Also if you want to keep this, please replace gpio by GPIO and pwms by PWMs. > +static int gpio_pwm_remove(struct platform_device *pdev) > +{ > + struct gpio_pwm_chip *gpio_chip; > + int i; unsigned int. > + > + gpio_chip = platform_get_drvdata(pdev); Any reason why you put this on the same line where you declare gpio_chip? > + for (i = 0; i < gpio_chip->chip.npwm; i++) { > + struct gpio_pwm_data *gpio_data; > + > + gpio_data = pwm_get_chip_data(&gpio_chip->chip.pwms[i]); > + > + hrtimer_cancel(&gpio_data->timer); > + } > + > + return pwmchip_remove(&gpio_chip->chip); > +} > + > +static const struct of_device_id gpio_pwm_of_match[] = { > + { .compatible = DRV_NAME, }, > + {/* sentinel */}, > +}; > +MODULE_DEVICE_TABLE(of, gpio_pwm_of_match); > + > +static struct platform_driver gpio_pwm_driver = { > + .probe = gpio_pwm_probe, > + .remove = gpio_pwm_remove, > + .driver = { > + .name = DRV_NAME, > + .of_match_table = of_match_ptr(gpio_pwm_of_match), No need for this conditional. You're effectively OF-only because of the call to of_gpio_named_count() in ->probe(). If you drop multiple-GPIO support you'll get non-OF support for free as far as I can tell, so one more reason to simplify. But then if you do support non-OF, you'll need to protect the OF device table with appropriate #ifdef guards, otherwise the compiler will complain about it being unused. Thierry
diff --git a/Documentation/devicetree/bindings/pwm/pwm-gpio.txt b/Documentation/devicetree/bindings/pwm/pwm-gpio.txt new file mode 100644 index 0000000..336f61f --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-gpio.txt @@ -0,0 +1,18 @@ +Generic GPIO bit-banged PWM driver + +Required properties: + - compatible: should be "pwm-gpio" + - #pwm-cells: should be 3, see pwm.txt in this directory for a general + description of the cells format. + - pwm-gpios: one or more gpios describing the used gpio, see the gpio + bindings for the used gpio driver. + +Example: +#include <dt-bindings/gpio/gpio.h> + + pwm: pwm@0 { + compatible = "pwm-gpio"; + #pwm-cells = 3; + pwm-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; + pwm-gpios = <&pio 7 2 GPIO_ACTIVE_LOW>; + }; diff --git a/MAINTAINERS b/MAINTAINERS index 7ba7ab7..0ae7fbf 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -4555,6 +4555,11 @@ F: drivers/i2c/muxes/i2c-mux-gpio.c F: include/linux/i2c-mux-gpio.h F: Documentation/i2c/muxes/i2c-mux-gpio +GENERIC GPIO PWM DRIVER +M: Olliver Schinagl <oliver@schinagl.nl> +S: Maintained +F: drivers/pwm/pwm-gpio.c + GENERIC HDLC (WAN) DRIVERS M: Krzysztof Halasa <khc@pm.waw.pl> W: http://www.kernel.org/pub/linux/utils/net/hdlc/ diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig index 0cfaf6b..c0bc296 100644 --- a/drivers/pwm/Kconfig +++ b/drivers/pwm/Kconfig @@ -170,6 +170,21 @@ config PWM_IMG To compile this driver as a module, choose M here: the module will be called pwm-img +config PWM_GPIO + tristate "Generic GPIO bit-banged PWM driver" + depends on OF + depends on GPIOLIB + help + Some platforms do not offer any hardware PWM capabilities but do have + General Purpose Input Output (GPIO) pins available. Using the kernels + High-Resolution Timer API this driver tries to toggle GPIO using the + generic kernel PWM framework. The maximum frequency and/or accuracy + is dependent on several factors such as system load and the maximum + speed a pin can be toggled at the hardware. + + To compile this driver as a module, choose M here: the module + will be called pwm-gpio. + config PWM_IMX tristate "i.MX PWM support" depends on ARCH_MXC diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile index 69b8275..96aa9aa 100644 --- a/drivers/pwm/Makefile +++ b/drivers/pwm/Makefile @@ -13,6 +13,7 @@ obj-$(CONFIG_PWM_CLPS711X) += pwm-clps711x.o obj-$(CONFIG_PWM_CRC) += pwm-crc.o obj-$(CONFIG_PWM_EP93XX) += pwm-ep93xx.o obj-$(CONFIG_PWM_FSL_FTM) += pwm-fsl-ftm.o +obj-$(CONFIG_PWM_GPIO) += pwm-gpio.o obj-$(CONFIG_PWM_IMG) += pwm-img.o obj-$(CONFIG_PWM_IMX) += pwm-imx.o obj-$(CONFIG_PWM_JZ4740) += pwm-jz4740.o diff --git a/drivers/pwm/pwm-gpio.c b/drivers/pwm/pwm-gpio.c new file mode 100644 index 0000000..8b588fb --- /dev/null +++ b/drivers/pwm/pwm-gpio.c @@ -0,0 +1,253 @@ +/* + * Copyright (c) 2015 Olliver Schinagl <oliver@schinagl.nl> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * This driver adds a high-resolution timer based PWM driver. Since this is a + * bit-banged driver, accuracy will always depend on a lot of factors, such as + * GPIO toggle speed and system load. + */ + +#include <linux/mod_devicetable.h> +#include <linux/module.h> +#include <linux/gpio/consumer.h> +#include <linux/of.h> +#include <linux/of_gpio.h> +#include <linux/property.h> +#include <linux/pwm.h> +#include <linux/errno.h> +#include <linux/err.h> +#include <linux/device.h> +#include <linux/hrtimer.h> +#include <linux/ktime.h> +#include <linux/kernel.h> +#include <linux/platform_device.h> + +#define DRV_NAME "pwm-gpio" + +struct gpio_pwm_data { + struct hrtimer timer; + struct gpio_desc *gpiod; + bool polarity; + bool pin_on; + int on_time; + int off_time; + bool run; +}; + +struct gpio_pwm_chip { + struct pwm_chip chip; +}; + +static void gpio_pwm_off(struct gpio_pwm_data *gpio_data) +{ + gpiod_set_value_cansleep(gpio_data->gpiod, gpio_data->polarity ? 0 : 1); +} + +static void gpio_pwm_on(struct gpio_pwm_data *gpio_data) +{ + gpiod_set_value_cansleep(gpio_data->gpiod, gpio_data->polarity ? 1 : 0); +} + +enum hrtimer_restart gpio_pwm_timer(struct hrtimer *timer) +{ + struct gpio_pwm_data *gpio_data = container_of(timer, + struct gpio_pwm_data, + timer); + if (!gpio_data->run) { + gpio_pwm_off(gpio_data); + gpio_data->pin_on = false; + return HRTIMER_NORESTART; + } + + if (!gpio_data->pin_on) { + hrtimer_forward_now(&gpio_data->timer, + ns_to_ktime(gpio_data->on_time)); + gpio_pwm_on(gpio_data); + gpio_data->pin_on = true; + } else { + hrtimer_forward_now(&gpio_data->timer, + ns_to_ktime(gpio_data->off_time)); + gpio_pwm_off(gpio_data); + gpio_data->pin_on = false; + } + + return HRTIMER_RESTART; +} + +static int gpio_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm, + int duty_ns, int period_ns) +{ + struct gpio_pwm_data *gpio_data = pwm_get_chip_data(pwm); + + gpio_data->on_time = duty_ns; + gpio_data->off_time = period_ns - duty_ns; + + return 0; +} + +static int gpio_pwm_set_polarity(struct pwm_chip *chip, struct pwm_device *pwm, + enum pwm_polarity polarity) +{ + struct gpio_pwm_data *gpio_data = pwm_get_chip_data(pwm); + + gpio_data->polarity = (polarity != PWM_POLARITY_NORMAL) ? true : false; + + return 0; +} + +static int gpio_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm) +{ + struct gpio_pwm_data *gpio_data = pwm_get_chip_data(pwm); + + if (gpio_data->run) + return -EBUSY; + + gpio_data->run = true; + if (gpio_data->off_time) { + hrtimer_start(&gpio_data->timer, ktime_set(0, 0), + HRTIMER_MODE_REL); + } else { + if (gpio_data->on_time) + gpio_pwm_on(gpio_data); + else + gpio_pwm_off(gpio_data); + } + + return 0; +} + +static void gpio_pwm_disable(struct pwm_chip *chip, struct pwm_device *pwm) +{ + struct gpio_pwm_data *gpio_data = pwm_get_chip_data(pwm); + + gpio_data->run = false; + if (!gpio_data->off_time) + gpio_pwm_off(gpio_data); +} + +static const struct pwm_ops gpio_pwm_ops = { + .config = gpio_pwm_config, + .set_polarity = gpio_pwm_set_polarity, + .enable = gpio_pwm_enable, + .disable = gpio_pwm_disable, + .owner = THIS_MODULE, +}; + +static int gpio_pwm_probe(struct platform_device *pdev) +{ + int ret; + struct gpio_pwm_chip *gpio_chip; + int npwm, i; + int hrtimer = 0; + + npwm = of_gpio_named_count(pdev->dev.of_node, "pwm-gpios"); + if (npwm < 1) + return -ENODEV; + + gpio_chip = devm_kzalloc(&pdev->dev, sizeof(*gpio_chip), GFP_KERNEL); + if (!gpio_chip) + return -ENOMEM; + + gpio_chip->chip.dev = &pdev->dev; + gpio_chip->chip.ops = &gpio_pwm_ops; + gpio_chip->chip.base = -1; + gpio_chip->chip.npwm = npwm; + gpio_chip->chip.of_xlate = of_pwm_xlate_with_flags; + gpio_chip->chip.of_pwm_n_cells = 3; + gpio_chip->chip.can_sleep = true; + + ret = pwmchip_add(&gpio_chip->chip); + if (ret < 0) { + dev_err(&pdev->dev, "failed to add PWM chip: %d\n", ret); + return ret; + } + + for (i = 0; i < npwm; i++) { + struct gpio_desc *gpiod; + struct gpio_pwm_data *gpio_data; + + gpiod = devm_gpiod_get_index(&pdev->dev, "pwm", i, + GPIOD_OUT_LOW); + if (IS_ERR(gpiod)) { + int error; + + error = PTR_ERR(gpiod); + if (error != -EPROBE_DEFER) + dev_err(&pdev->dev, + "failed to get gpio flags, error: %d\n", + error); + return error; + } + + gpio_data = devm_kzalloc(&pdev->dev, sizeof(*gpio_data), + GFP_KERNEL); + + hrtimer_init(&gpio_data->timer, + CLOCK_MONOTONIC, HRTIMER_MODE_REL); + gpio_data->timer.function = &gpio_pwm_timer; + gpio_data->gpiod = gpiod; + gpio_data->pin_on = false; + gpio_data->run = false; + + if (hrtimer_is_hres_active(&gpio_data->timer)) + hrtimer++; + + pwm_set_chip_data(&gpio_chip->chip.pwms[i], gpio_data); + } + if (!hrtimer) + dev_warn(&pdev->dev, "unable to use High-Resolution timer,"); + dev_warn(&pdev->dev, "%s is restricted to low resolution.", + DRV_NAME); + + platform_set_drvdata(pdev, gpio_chip); + + dev_info(&pdev->dev, "%d gpio pwms loaded\n", npwm); + + return 0; +} + +static int gpio_pwm_remove(struct platform_device *pdev) +{ + struct gpio_pwm_chip *gpio_chip; + int i; + + gpio_chip = platform_get_drvdata(pdev); + for (i = 0; i < gpio_chip->chip.npwm; i++) { + struct gpio_pwm_data *gpio_data; + + gpio_data = pwm_get_chip_data(&gpio_chip->chip.pwms[i]); + + hrtimer_cancel(&gpio_data->timer); + } + + return pwmchip_remove(&gpio_chip->chip); +} + +static const struct of_device_id gpio_pwm_of_match[] = { + { .compatible = DRV_NAME, }, + {/* sentinel */}, +}; +MODULE_DEVICE_TABLE(of, gpio_pwm_of_match); + +static struct platform_driver gpio_pwm_driver = { + .probe = gpio_pwm_probe, + .remove = gpio_pwm_remove, + .driver = { + .name = DRV_NAME, + .of_match_table = of_match_ptr(gpio_pwm_of_match), + }, +}; +module_platform_driver(gpio_pwm_driver); + +MODULE_AUTHOR("Olliver Schinagl <oliver@schinagl.nl>"); +MODULE_DESCRIPTION("Generic GPIO bit-banged PWM driver"); +MODULE_LICENSE("GPL");