Message ID | 1427986842-21409-1-git-send-email-tomeu.vizoso@collabora.com |
---|---|
State | Superseded, archived |
Headers | show |
Reviewed-by: Mikko Perttunen <mikko.perttunen@kapsi.fi> On 04/02/2015 06:00 PM, Tomeu Vizoso wrote: > It should be the first controller, not the second. > > This broke USB after 6261b06 ("regulator: Defer lookup of supply to > regulator_get"), because it changed the order in which the controllers > were probed. > > The fix for this issue was suggested by Mikko Perttunen. > > Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com> > Cc: Mikko Perttunen <mikko.perttunen@kapsi.fi> > --- > > I think that the line numbers should be enough in this case, as I expect this to be merged soon, but just in case I'm sending the same patch with plenty of context. > > Regards, > > Tomeu > > --- > arch/arm/boot/dts/tegra124.dtsi | 2 +- > 1 file changed, 1 insertion(+), 1 deletion(-) > > diff --git a/arch/arm/boot/dts/tegra124.dtsi b/arch/arm/boot/dts/tegra124.dtsi > index cf01c81..cb786a9 100644 > --- a/arch/arm/boot/dts/tegra124.dtsi > +++ b/arch/arm/boot/dts/tegra124.dtsi > @@ -821,77 +821,77 @@ > compatible = "nvidia,tegra124-usb-phy", "nvidia,tegra30-usb-phy"; > reg = <0x0 0x7d000000 0x0 0x4000>, > <0x0 0x7d000000 0x0 0x4000>; > phy_type = "utmi"; > clocks = <&tegra_car TEGRA124_CLK_USBD>, > <&tegra_car TEGRA124_CLK_PLL_U>, > <&tegra_car TEGRA124_CLK_USBD>; > clock-names = "reg", "pll_u", "utmi-pads"; > resets = <&tegra_car 59>, <&tegra_car 22>; > reset-names = "usb", "utmi-pads"; > nvidia,hssync-start-delay = <0>; > nvidia,idle-wait-delay = <17>; > nvidia,elastic-limit = <16>; > nvidia,term-range-adj = <6>; > nvidia,xcvr-setup = <9>; > nvidia,xcvr-lsfslew = <0>; > nvidia,xcvr-lsrslew = <3>; > nvidia,hssquelch-level = <2>; > nvidia,hsdiscon-level = <5>; > nvidia,xcvr-hsslew = <12>; > + nvidia,has-utmi-pad-registers; > status = "disabled"; > }; > > usb@0,7d004000 { > compatible = "nvidia,tegra124-ehci", "nvidia,tegra30-ehci", "usb-ehci"; > reg = <0x0 0x7d004000 0x0 0x4000>; > interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; > phy_type = "utmi"; > clocks = <&tegra_car TEGRA124_CLK_USB2>; > resets = <&tegra_car 58>; > reset-names = "usb"; > nvidia,phy = <&phy2>; > status = "disabled"; > }; > > phy2: usb-phy@0,7d004000 { > compatible = "nvidia,tegra124-usb-phy", "nvidia,tegra30-usb-phy"; > reg = <0x0 0x7d004000 0x0 0x4000>, > <0x0 0x7d000000 0x0 0x4000>; > phy_type = "utmi"; > clocks = <&tegra_car TEGRA124_CLK_USB2>, > <&tegra_car TEGRA124_CLK_PLL_U>, > <&tegra_car TEGRA124_CLK_USBD>; > clock-names = "reg", "pll_u", "utmi-pads"; > resets = <&tegra_car 22>, <&tegra_car 22>; > reset-names = "usb", "utmi-pads"; > nvidia,hssync-start-delay = <0>; > nvidia,idle-wait-delay = <17>; > nvidia,elastic-limit = <16>; > nvidia,term-range-adj = <6>; > nvidia,xcvr-setup = <9>; > nvidia,xcvr-lsfslew = <0>; > nvidia,xcvr-lsrslew = <3>; > nvidia,hssquelch-level = <2>; > nvidia,hsdiscon-level = <5>; > nvidia,xcvr-hsslew = <12>; > - nvidia,has-utmi-pad-registers; > status = "disabled"; > }; > > usb@0,7d008000 { > compatible = "nvidia,tegra124-ehci", "nvidia,tegra30-ehci", "usb-ehci"; > reg = <0x0 0x7d008000 0x0 0x4000>; > interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; > phy_type = "utmi"; > clocks = <&tegra_car TEGRA124_CLK_USB3>; > resets = <&tegra_car 59>; > reset-names = "usb"; > nvidia,phy = <&phy3>; > status = "disabled"; > }; > > phy3: usb-phy@0,7d008000 { > compatible = "nvidia,tegra124-usb-phy", "nvidia,tegra30-usb-phy"; > reg = <0x0 0x7d008000 0x0 0x4000>, > <0x0 0x7d000000 0x0 0x4000>; > phy_type = "utmi"; > -- To unsubscribe from this list: send the line "unsubscribe linux-tegra" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 04/02/2015 06:20 PM, Mikko Perttunen wrote: > Reviewed-by: Mikko Perttunen <mikko.perttunen@kapsi.fi> Scratch that; as Tuomas noted on IRC, the reset numbers here are still wrong. phy1 should have 22 and phy2 58. > > On 04/02/2015 06:00 PM, Tomeu Vizoso wrote: >> It should be the first controller, not the second. >> >> This broke USB after 6261b06 ("regulator: Defer lookup of supply to >> regulator_get"), because it changed the order in which the controllers >> were probed. >> >> The fix for this issue was suggested by Mikko Perttunen. >> >> Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com> >> Cc: Mikko Perttunen <mikko.perttunen@kapsi.fi> >> --- >> >> I think that the line numbers should be enough in this case, as I >> expect this to be merged soon, but just in case I'm sending the same >> patch with plenty of context. >> >> Regards, >> >> Tomeu >> >> --- >> arch/arm/boot/dts/tegra124.dtsi | 2 +- >> 1 file changed, 1 insertion(+), 1 deletion(-) >> >> diff --git a/arch/arm/boot/dts/tegra124.dtsi >> b/arch/arm/boot/dts/tegra124.dtsi >> index cf01c81..cb786a9 100644 >> --- a/arch/arm/boot/dts/tegra124.dtsi >> +++ b/arch/arm/boot/dts/tegra124.dtsi >> @@ -821,77 +821,77 @@ >> compatible = "nvidia,tegra124-usb-phy", >> "nvidia,tegra30-usb-phy"; >> reg = <0x0 0x7d000000 0x0 0x4000>, >> <0x0 0x7d000000 0x0 0x4000>; >> phy_type = "utmi"; >> clocks = <&tegra_car TEGRA124_CLK_USBD>, >> <&tegra_car TEGRA124_CLK_PLL_U>, >> <&tegra_car TEGRA124_CLK_USBD>; >> clock-names = "reg", "pll_u", "utmi-pads"; >> resets = <&tegra_car 59>, <&tegra_car 22>; >> reset-names = "usb", "utmi-pads"; >> nvidia,hssync-start-delay = <0>; >> nvidia,idle-wait-delay = <17>; >> nvidia,elastic-limit = <16>; >> nvidia,term-range-adj = <6>; >> nvidia,xcvr-setup = <9>; >> nvidia,xcvr-lsfslew = <0>; >> nvidia,xcvr-lsrslew = <3>; >> nvidia,hssquelch-level = <2>; >> nvidia,hsdiscon-level = <5>; >> nvidia,xcvr-hsslew = <12>; >> + nvidia,has-utmi-pad-registers; >> status = "disabled"; >> }; >> >> usb@0,7d004000 { >> compatible = "nvidia,tegra124-ehci", "nvidia,tegra30-ehci", >> "usb-ehci"; >> reg = <0x0 0x7d004000 0x0 0x4000>; >> interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; >> phy_type = "utmi"; >> clocks = <&tegra_car TEGRA124_CLK_USB2>; >> resets = <&tegra_car 58>; >> reset-names = "usb"; >> nvidia,phy = <&phy2>; >> status = "disabled"; >> }; >> >> phy2: usb-phy@0,7d004000 { >> compatible = "nvidia,tegra124-usb-phy", >> "nvidia,tegra30-usb-phy"; >> reg = <0x0 0x7d004000 0x0 0x4000>, >> <0x0 0x7d000000 0x0 0x4000>; >> phy_type = "utmi"; >> clocks = <&tegra_car TEGRA124_CLK_USB2>, >> <&tegra_car TEGRA124_CLK_PLL_U>, >> <&tegra_car TEGRA124_CLK_USBD>; >> clock-names = "reg", "pll_u", "utmi-pads"; >> resets = <&tegra_car 22>, <&tegra_car 22>; >> reset-names = "usb", "utmi-pads"; >> nvidia,hssync-start-delay = <0>; >> nvidia,idle-wait-delay = <17>; >> nvidia,elastic-limit = <16>; >> nvidia,term-range-adj = <6>; >> nvidia,xcvr-setup = <9>; >> nvidia,xcvr-lsfslew = <0>; >> nvidia,xcvr-lsrslew = <3>; >> nvidia,hssquelch-level = <2>; >> nvidia,hsdiscon-level = <5>; >> nvidia,xcvr-hsslew = <12>; >> - nvidia,has-utmi-pad-registers; >> status = "disabled"; >> }; >> >> usb@0,7d008000 { >> compatible = "nvidia,tegra124-ehci", "nvidia,tegra30-ehci", >> "usb-ehci"; >> reg = <0x0 0x7d008000 0x0 0x4000>; >> interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; >> phy_type = "utmi"; >> clocks = <&tegra_car TEGRA124_CLK_USB3>; >> resets = <&tegra_car 59>; >> reset-names = "usb"; >> nvidia,phy = <&phy3>; >> status = "disabled"; >> }; >> >> phy3: usb-phy@0,7d008000 { >> compatible = "nvidia,tegra124-usb-phy", >> "nvidia,tegra30-usb-phy"; >> reg = <0x0 0x7d008000 0x0 0x4000>, >> <0x0 0x7d000000 0x0 0x4000>; >> phy_type = "utmi"; >> > > -- > To unsubscribe from this list: send the line "unsubscribe linux-tegra" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-tegra" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/arch/arm/boot/dts/tegra124.dtsi b/arch/arm/boot/dts/tegra124.dtsi index cf01c81..cb786a9 100644 --- a/arch/arm/boot/dts/tegra124.dtsi +++ b/arch/arm/boot/dts/tegra124.dtsi @@ -821,77 +821,77 @@ compatible = "nvidia,tegra124-usb-phy", "nvidia,tegra30-usb-phy"; reg = <0x0 0x7d000000 0x0 0x4000>, <0x0 0x7d000000 0x0 0x4000>; phy_type = "utmi"; clocks = <&tegra_car TEGRA124_CLK_USBD>, <&tegra_car TEGRA124_CLK_PLL_U>, <&tegra_car TEGRA124_CLK_USBD>; clock-names = "reg", "pll_u", "utmi-pads"; resets = <&tegra_car 59>, <&tegra_car 22>; reset-names = "usb", "utmi-pads"; nvidia,hssync-start-delay = <0>; nvidia,idle-wait-delay = <17>; nvidia,elastic-limit = <16>; nvidia,term-range-adj = <6>; nvidia,xcvr-setup = <9>; nvidia,xcvr-lsfslew = <0>; nvidia,xcvr-lsrslew = <3>; nvidia,hssquelch-level = <2>; nvidia,hsdiscon-level = <5>; nvidia,xcvr-hsslew = <12>; + nvidia,has-utmi-pad-registers; status = "disabled"; }; usb@0,7d004000 { compatible = "nvidia,tegra124-ehci", "nvidia,tegra30-ehci", "usb-ehci"; reg = <0x0 0x7d004000 0x0 0x4000>; interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; phy_type = "utmi"; clocks = <&tegra_car TEGRA124_CLK_USB2>; resets = <&tegra_car 58>; reset-names = "usb"; nvidia,phy = <&phy2>; status = "disabled"; }; phy2: usb-phy@0,7d004000 { compatible = "nvidia,tegra124-usb-phy", "nvidia,tegra30-usb-phy"; reg = <0x0 0x7d004000 0x0 0x4000>, <0x0 0x7d000000 0x0 0x4000>; phy_type = "utmi"; clocks = <&tegra_car TEGRA124_CLK_USB2>, <&tegra_car TEGRA124_CLK_PLL_U>, <&tegra_car TEGRA124_CLK_USBD>; clock-names = "reg", "pll_u", "utmi-pads"; resets = <&tegra_car 22>, <&tegra_car 22>; reset-names = "usb", "utmi-pads"; nvidia,hssync-start-delay = <0>; nvidia,idle-wait-delay = <17>; nvidia,elastic-limit = <16>; nvidia,term-range-adj = <6>; nvidia,xcvr-setup = <9>; nvidia,xcvr-lsfslew = <0>; nvidia,xcvr-lsrslew = <3>; nvidia,hssquelch-level = <2>; nvidia,hsdiscon-level = <5>; nvidia,xcvr-hsslew = <12>; - nvidia,has-utmi-pad-registers; status = "disabled"; }; usb@0,7d008000 { compatible = "nvidia,tegra124-ehci", "nvidia,tegra30-ehci", "usb-ehci"; reg = <0x0 0x7d008000 0x0 0x4000>; interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; phy_type = "utmi"; clocks = <&tegra_car TEGRA124_CLK_USB3>; resets = <&tegra_car 59>; reset-names = "usb"; nvidia,phy = <&phy3>; status = "disabled"; }; phy3: usb-phy@0,7d008000 { compatible = "nvidia,tegra124-usb-phy", "nvidia,tegra30-usb-phy"; reg = <0x0 0x7d008000 0x0 0x4000>, <0x0 0x7d000000 0x0 0x4000>; phy_type = "utmi";
It should be the first controller, not the second. This broke USB after 6261b06 ("regulator: Defer lookup of supply to regulator_get"), because it changed the order in which the controllers were probed. The fix for this issue was suggested by Mikko Perttunen. Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com> Cc: Mikko Perttunen <mikko.perttunen@kapsi.fi> --- I think that the line numbers should be enough in this case, as I expect this to be merged soon, but just in case I'm sending the same patch with plenty of context. Regards, Tomeu --- arch/arm/boot/dts/tegra124.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)